manualshive.com logo in svg

Raynor ControlHoist CMT, Руководство по установке

Поделиться
Скачать
Raynor ControlHoist CMT Скачать руководство пользователя страница 12

12

5.3

Limit Switch Adjustment

Table 3 - Limit Switch Adjustment Procedures

Limit Switch

Adjustment Procedures 

Open Limit

1. Move the open cam close to the open limit switch and proceed as per described in section

Operator Start-up, Table 6, p.26.

2. Release cam-retaining bracket and make sure that the bracket 

engages

 in the slots of 

both cams.

Advanced

Close Limit 

1. Pull the disconnect chain for manual operation.

2. Manually open the door approx. 6” above the ground.

3. Pull the cam-retaining bracket from the Close side, see Figure 5, and rotate Close cam 

manually until it activates the Close limit switch sufficiently so that a “click” can be heard.

4. Release cam-retaining bracket and make sure that the bracket 

engages

 in the slots of 

both cams.

Limit Switch

Fine

Adjustment

1. Limit switch fine adjustment SHOULD be done after the main power supply is connected 

to the operator. Refer to section Operator Start-up, Table 6, p.26.
Note: One (1) notch on cam is equal (=) to approximately ½” of the door travel.

For technical support, please call 

1-800-4-Raynor (1-800-472-9667)

 or visit 

www.raynor.com

Содержание ControlHoist CMT













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды