background image

1.

 

Introduction

 

 
This Handbook describes how to operate your ST7000 and is intended for use after the autopilot has been set up.  
Full details of setting up and initial sea trials procedures are described in the Installation Handbook. 
 

Basic Principles

 

When switched on, the ST7000 will be in Standby mode.  To select automatic steering simply steady the vessel on 
the required heading and push Auto.  At any time to return to manual steering push Standby. 
Autopilot control has been simplified to a set of push button operations, all of which are confirmed with a beep tone.  
In addition to the main 6 button course control keypad, the secondary 4 button keypad provides the following 
functions:- 

• 

Track 

selects the built in track control to allow the autopilot to steer under the supervision of Radio Navigation 
System. 

• 

Response 

selects 3 levels of course keeping response. 

• 

Display 

 selects 

1)  waypoint information for display (when available). 
2)  the watch alarm. 
3) illumination 

level. 

 

Warning

 

Hand steering is not possible when 'Auto' is

 

selected.  The 'Standby' button must be

 

pressed to 

disengage the Autopilot drive.

 

It is the skippers responsibility to brief

 

all crew members on this procedure.

 

When used with a Sterndrive Actuator a

 

special 

emergency manual override facility

 

is provided.  For 

details see page 13.

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

2

Содержание ST7000





















Отзывы: