Raymarine RC435i Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 128

background image

Chapter 2: Installation

7

Chapter 2: Installation

2.1 Introduction

This chapter provides instructions to assist in planning the installation of
the RC435/435i Chartplotter aboard your vessel.

Note:

If you wish to practice using the RC435/435i Chartplotter before

installation, you can connect it, via a 1A quick blow fuse, to a 12VDC
power supply and operate it using the simulator mode, as described in
Chapter 3:Getting Started.

EMC Installation Guidelines

All Raymarine equipment and accessories are designed to the best
industry standards for use in the recreational marine environment.

Their design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) standards, but correct installation
is required to ensure that performance is not compromised. Although
every effort has been taken to ensure that they will perform under all
conditions, it is important to understand what factors could affect the
operation of the product.

For optimum EMC performance, it is recommended that wherever
possible:

•

Raymarine equipment and cables connected to it are:
• At least 3 ft (1 m) from any equipment transmitting or cables carry-

ing radio signals (for example: VHF radios, cables and antennas.)

• More than 7 ft (2 m) from the path of a radar beam. A radar beam

can normally be assumed to spread 20 degrees above and below
the radiating element.

•

Raymarine specified cables are used. Cutting and rejoining these
cables can compromise EMC performance and must be avoided
unless doing so is detailed in the installation manual.

•

If a suppression ferrite is attached to a cable, this ferrite should not be
removed. If the ferrite needs to be removed during installation it must
be reassembled in the same position.

Suppression Ferrites

The following illustration shows typical cable suppression ferrites used
with Raymarine equipment. Always use the ferrites supplied by
Raymarine.

«
...
15
16
17
18
19
...
»

Содержание RC435i

































































































































Отзывы:

Нет отзывов

Похожие инструкции для RC435i

010-11018-00 - Mobile PC - GPS Software

Бренд: Garmin Страницы: 1

Бренд: Holux Страницы: 3

Бренд: TRACKIMO Страницы: 9

CAREU U1 Lite(WR)

Бренд: S&T Страницы: 28

Бренд: Teltonika Страницы: 155

Бренд: Garmin Страницы: 38

Tracking Smart ET005

Бренд: Vjoy Car Страницы: 14

USBL BROADBAND ACOUSTIC TRACKING SYSTEM

Бренд: Edgetech Страницы: 102

Бренд: Spectrum Страницы: 9

10000170 - 2100 - Automotive GPS Receiver

Бренд: Navigon Страницы: 104

Бренд: Transplant Computing Страницы: 30

FreeWAY SX 7.2 IPS

Бренд: Modecom Страницы: 4

Бренд: Tele System Страницы: 56

Zumo 200 Series

Бренд: Garmin Страницы: 58

Бренд: Garmin Страницы: 24

Бренд: Garmin Страницы: 74

Бренд: Garmin Страницы: 2

Бренд: Datablaze Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды