Raymarine E12207 Скачать руководство пользователя | Manualshive

Страница: 7 / 42

background image

Chapter 1: Important information

Handbook information

This handbook contains important information regarding the
Hydraulic Linear Drives.

The handbook is for use with the following models:

Part number

Type

Voltage

E12207 (replaces
M81200)

Type 2

12 V

E12208 (replaces
M81201)

Type 2

24 V

M81202

Type 3

12 V

M81203

Type 3

24 V

Additional handbooks

The following handbooks provide additional information relating to
the operation of the Hydraulic Linear Drive, and compatible course
computers.

Description

Part number

SPX System Installation guide

87072

SPX System Commissioning
Instructions

81287

SeaTalk

ng

Reference Manual

81300

Certified Installation

Raymarine recommends certified installation by a Raymarine
approved installer. A certified installation qualifies for enhanced
product warranty benefits. Contact your Raymarine dealer for
further details, and refer to the separate warranty document packed
with your product.

Warning: Product installation and
operation

This product must be installed and operated in
accordance with the instructions provided. Failure to
do so could result in personal injury, damage to your
boat and/or poor product performance.

Warning: Switch off power supply

Ensure the boat’s power supply is switched OFF
before starting to install this product. Do NOT connect
or disconnect equipment with the power switched on,
unless instructed in this document.

Warning: Entrapment hazard

This product features moving parts that provide a
potential entrapment hazard. Keep clear of moving
parts at all times.

Warning: Do NOT flash test

Do NOT perform an electrical flash test on this product.

Important information

7

«
...
5
6
7
8
9
...
»

Содержание E12207











































Отзывы:

Нет отзывов

Похожие инструкции для E12207

Бренд: E-Mu Страницы: 72

Бренд: E-Mu Страницы: 44

Бренд: Panasonic Страницы: 2

Бренд: Sierra Страницы: 11

Бренд: Water Control Страницы: 20

Бренд: JVC Страницы: 56

Бренд: JVC Страницы: 41

Бренд: JVC Страницы: 48

Бренд: JVC Страницы: 74

Бренд: JVC Страницы: 28

Бренд: JVC Страницы: 82

Бренд: JVC Страницы: 31

Бренд: JVC Страницы: 87

Бренд: JVC Страницы: 94

Бренд: JVC Страницы: 59

Бренд: JVC Страницы: 28

Бренд: JVC Страницы: 26

Бренд: JVC Страницы: 208

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды