Raymar Myriad MD9612FP Скачать руководство пользователя

Страница: 3 / 33

MD9612FP USER’S GUIDE

0049-1237-XXX

Page iii

REV.

Compliances

This device complies with Part 15A of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15A of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit other than the one

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

If none of these actions resolves the problem, consult your distributor or

an experienced radio/television technician for additional suggestions.

Additionally, Section 15.838, paragraph d), of the FCC Rules and

Regulations states: “Where special accessories, such as shielded cables,

are required in order to meet FCC regulations, shielded cables must be

used with this equipment. Operation with non-approved equipment or

unshielded cables is likely to result in interference to radio and TV

reception. The user is cautioned that changes and modifications to this

equipment without the approval of the manufacturer could void the user’s

authority to operate this equipment.

Содержание Myriad MD9612FP


































Результаты поиска

Содержание Myriad MD9612FP

Отзывы:

Похожие инструкции для Myriad MD9612FP

Бренды по названию

Популярные бренды

Raymar Myriad MD9612FP, Руководство пользователя

Результаты поиска

Содержание Myriad MD9612FP

Отзывы:

Похожие инструкции для Myriad MD9612FP

Бренды по названию

Популярные бренды