Raymar Myriad MD9612FP Скачать руководство пользователя | Manualshive

Страница: 24 / 33

background image

MD9612FP USER’S GUIDE

0049-1237-XXX

Page 20

REV.

A

Leased lines have four contacts: a transmit (Tx) pair and a receive (Rx)

pair. For communication to occur:

The Rx line of the modem cage or modem rack RJ-11 jack must

connect to the Tx line of the other modem.

The Tx line of the modem cage or modem rack RJ-11 jack must

connect to the Rx line of the other modem.

For more information, refer to the documentation that came with your

modem cage or modem rack.

Connecting an RS-232 Device

The modem cage or modem rack has different RS-232 options for

accepting an attached RS-232 (RTU) device. Your version may have a

female 25-pin RS-232 connector for each slot in the modem cage or

modem rack.

«
...
22
23
24
25
26
...
»

Содержание Myriad MD9612FP


































Отзывы:

Нет отзывов

Похожие инструкции для Myriad MD9612FP

Бренд: Linksys Страницы: 24

Бренд: iRZ Страницы: 19

Бренд: Aztech Страницы: 16

HFB-FO-LON Series

Бренд: Buenoptic Страницы: 8

Бренд: Four-Faith Страницы: 34

Gigaset SE680 WiMAX

Бренд: Gigaset Страницы: 62

Gigaset SE587 WLAN dsl

Бренд: Gigaset Страницы: 89

Бренд: Micro-Aide Страницы: 48

ARRIS SURFboard SB6183

Бренд: CommScope Страницы: 28

Бренд: Zte Страницы: 9

Бренд: Franklin Technology Страницы: 40

TFM-560U - 56 Kbps Fax

Бренд: TRENDnet Страницы: 33

Бренд: Zoomtak Telephonics Страницы: 36

Xstream 1300 Series

Бренд: Tainet Страницы: 86

Бренд: Daktronics Страницы: 3

Бренд: Haier Страницы: 39

Бренд: Haier Страницы: 52

Бренд: Haier Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды