manualshive.com logo in svg

Raycus RFL-C Series, Руководство пользователя, Страница: 33 / 47

Поделиться
Скачать
Raycus RFL-C Series Скачать руководство пользователя страница 33

Wuhan Raycus Fiber Laser Technologies Co., Ltd.

 

User Guide 100W

~

750W Ver: 1.0                                                                                      

                             

20

 

System has started, please wait... 

If ‘Laser emission is not disabled, please power off the laser and check if LASER button on the 

front panel is pressed down’ is present in the self-check process, please follow the instructions to 

check the laser emission button on the front panel, press it to release, and then restart the product 

with the key. Laser emission must be enabled after system self-check is passed. 

Checking RS-232 connection............................ 

RS-232 connected.......................................... 

System is doing self-check, please wait........ 

Interlock is OK................................................ 

The Laser emission is initially enabled, please power off the laser and check if LASER button on 

the front panel is pressed down…....................... 

If ‘Interlock error, please power off the laser and check interlock’ is presented, follow the 

instructions accordingly, short the interlock, and then start the product again. 

Checking RS-232 connection............................ 

RS-232 connected.......................................... 

System is doing self-check, please wait........ 

Interlock error, please power off the laser and check interlock connection 

 

When ‘System has started, please wait…………..’ is presented, self-check is passed, then error 

records will be presented, followed be an instruction to press ‘U’ on the keyboard in 3 seconds. 

Error 1 record is 0 

Error 2 record is 0 

Error 3 record is 0 

Error 4 record is 0 

Error 5 record is 0 

Press ‘U’ in 3 seconds to enter UI 

Содержание RFL-C Series
















































Отзывы:

Нет отзывов