RaycoWylie i4507 Скачать руководство пользователя страница 23

Страница: 23 / 78

i4507 Offshore Lattice Boom Crane

Instruction Manual

55M4507OBE00-B

2.3 Operating Buttons Description

DUTY BUTTON

Choose this button to access the menu for the selection

of the duty number. Use the arrows “up” and “down” to

select the desired configuration.

ESCAPE BUTTON

Select

Escape

button to exit a menu or any

programming window without saving any changes and

to go back to the previous screen.

Select repeatedly to return to the main screen.

UP BUTTON

Select this button to scroll up through menu options or to

increase adjustable values.

DOWN BUTTON

Select this button to scroll

down through menu options

or to

decrease adjustable values.

MODE BUTTON

Enables you to select the operation mode. Select this

button to choose one of these main operating modes:

-Limit Mode

-Diagnostic Mode

Config. Mode

-Calibration Mode (protected by a password)

-Info Mode

-Error Mode

-Night Mode

Содержание i4507















































































Результаты поиска

Содержание i4507

Отзывы:

Бренды по названию

Популярные бренды

RaycoWylie i4507, Инструкция по эксплуатации

Результаты поиска

Содержание i4507

Отзывы:

Бренды по названию

Популярные бренды