RaycoWylie i4507 Скачать руководство пользователя страница 18

Страница: 18 / 78

55M4507OBE00-B

i4507 Offshore Lattice Boom Crane

Instruction Manual

1.5 Description of Typical Components

i4507 Display Box

It is the central processing unit (CPU) of the i4507

system.

It uses a CANbus network and is equipped

with a 7 inch color display.

Angle Sensor

The angle sensor is used to monitor the boom angle.

This inclinometer typically has a degree range of -10

to +90 degrees.

Load Sensor(s)

The load sensor is used to calculate the load on hook. It

can be a dynamometer or a dead-end load link. Others

options available upon request.

Termination Unit

This interface is connected to the various I/O sensors

installed on the crane. It transmits the information

to the i4507 display box using the CANbus network.

Optional explosion proof enclosure available.

Anti-two Block (optional)

he anti-two block switch prevent the hook block to

be pulled against the boom head. It is attached to the

boom tip on one end and to a chain leading to a weight

clamped around the hoist line at the other end. When

the block lifts the weight, it issues a warning and can

stops the upward movement.

Содержание i4507















































































Результаты поиска

Содержание i4507

Отзывы:

Бренды по названию

Популярные бренды

RaycoWylie i4507, Инструкция по эксплуатации

Результаты поиска

Содержание i4507

Отзывы:

Бренды по названию

Популярные бренды