background image

The heat exchanger is manufactured from a high quality stainless steel and where permitted by local water 
authorities may be used on direct hot water systems, although it is preferable to use the indirect system. 
Alternatively, the Rayburn Cookmaster 300K is a non-boiler model. However with this model the 

IDLING 

TEMPERATURE MAY BE HIGHER

These appliances must only be used with Commercial Kerosene current issue to BS 2869: Class C2 suitable for
vapourising burners. 

IMPORTANT:  IN  ORDER  TO  ACHIEVE  THE  OPTIMUM  PERFORMANCE  FROM  THIS  APPLIANCE,  IT  IS
ESSENTIAL  THAT  THE  INITIAL  COMMISSIONING  OF  THE  APPLIANCE  IS  UNDERTAKEN  BY  SELECTED, 
TRAINED INSTALLING SERVICE ENGINEERS (SUCH AS OFTEC APPROVED). 

YOUR RAYBURN STOCKIST WILL PROVIDE ADVICE ON THE LOCATION OF THE NEAREST INSTALLING
ENGINEER.  WE  ALSO  RECOMMEND  YOU  CONTRACT  OUT  THE  PERIODIC  SERVICING  OF  THE
APPLIANCE TO THIS INSTALLING SERVICING ENGINEER. 

THIS APPLIANCE IS A CONTROLLED SERVICE BY DEFINITION AND REQUIRES EITHER FITMENT UNDER
THE  REMIT  OF  BUILDING  CONTROL  OR  INSTALLATION  BY  AN  OFTEC  REGISTERED  105  TECHNICIAN
(CLASSED AS A COMPETENT PERSON) WHO CAN SELF CERTIFY HIS OWN WORKS. 

REMEMBER,  when  replacing  a  part  on  this  appliance,  use  only  spare  parts  that  you  can  be  assured
conform  to  the  safety  and  performance  specification  that  we  require.  Do  not  use  reconditioned  or  copy
parts that have not been clearly authorised by AGA. 

[email protected]

   

  

  

Boiler Model - 308K

 

Non-Boiler Model 300K

 

  

Cooker 

Cooker 

Cooker 

Cooker 

LOW 

HIGH 

LOW 

HIGH 

Heat Input 

kW  

Btu/h 

2.78  

9,497 

7.42  

25,321 

2.16  

7,386 

5.48  

18,700 

Heat Output Water 

kW  

Btu/h 

0.59  

2,000 

2.34  

8,000 

  

  

  

Oil Input 

cc/minute 

4.5 

12.0 

3.5 

8.5 - 9.0 

Boiler Water Connections 

Weight of Appliance 

300Kg 

Flow (one) Rp 1 (1in BSP Int) 

 Overall Dimensions 

Height: 995mm 

Width: 940mm 

Depth: 655mm  

Return (one) Rp1 (1in BSP Int) 

Both connections are located towards the 

rear 

edge of the appliance L.H. side panel.

 

FUEL - COMMERCIALKEROSENE current issue to 

BS.2869: Class C2 suitable for vapourising burners  

  

Oil Valve Inlet  Rp¼(¼in BSP Int) 

Flue Outlet Dia.  102mm 

Page 2 of 23

EINS 511985

26/10/2006

file://\\server1\docs\NetCDs\Aga%20Product%20Information%20Spares%20and%20Tec...

Содержание Cookmaster 300K
























Отзывы: