manualshive.com logo in svg

Raven SBGuidance Auto, Руководство по установке

Поделиться
Скачать
Raven SBGuidance Auto Скачать руководство пользователя страница 23

  

 

SBGuidance Auto I Rev. A I CAN 

SBG-Auto CAN-EN-Rev. A I Page 23/52 

 

4.

 

Mounting the wiring harness 

The total SBG cable harness exist of several cables, 
from the battery to the terminal (see Figure 53 and 
Figure 54). SBG offers two power harness options; the 
CAN Basic harness or the Implement Ready (IR) 
harness. As an in-cab terminal harness SBG offers a 
harness to connect the Viper 4(+) or the older GeoStar 
terminal. With an adapter harness it is also possible to 
connect a Viper 4(+) to the GeoStar terminal harness.  

4.1

 

CAN Basic Power harness 

The basic harness can only be used for tractor steering. 
If the tractor is fitted with this harness, it is not 
possible to use the tractor for implement steering 
(TWIN, plough). 

4.2

 

CAN Implement Ready (IR) Power harness 

With an Implement Ready harness the tractor can be 
used both for tractor and implement steering. The 
IBBC connector can be used to connect an implement 
(Figure 12). The Implement Ready power harness runs 
from the battery to the IBBC connector at the rear of 
the tractor. It branches off to connect the STU chassis 
harness and contains fuses near the split.  

 

 

Figure 12 IBBC bracket with connector.

 

Содержание SBGuidance Auto





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды