![background image](http://html.mh-extra.com/html/raven/rs1/rs1_calibration-and-operation-manual_788758008.webp)
CHAPTER 1
2
Manual Title
• Carefully read and follow all safety requirements and precautions contained in this manual and the machine-
specific Installation Manual. Failure to follow safety instructions may lead to equipment damage, personal
injury, or death.
• When starting the machine for the first time after installing RS1, be sure that all persons stand clear in case a
hose has not been properly tightened.
• The machine must remain stationary and switched off during RS1 installation or maintenance.
HYDRAULIC SAFETY
When installing or servicing a hydraulic system or hydraulic components, be aware that hydraulic fluid may be
extremely hot and under high pressure. Caution must be exercised.
• Always wear appropriate personal protective equipment when installing or servicing hydraulic systems.
• Never attempt to open or work on a hydraulic system with the implement running.
• Any work performed on the hydraulic system must be done in accordance with the machine manufacturer’s
approved maintenance instructions.
• Care should always be taken when servicing or opening a system that has been pressurized.
• The implement or machine must remain stationary and switched off with booms or implement sections
unfolded and supported during installation or maintenance.
• Take precautions to prevent foreign material or contaminants from being introduced into the implement
hydraulic system. Contaminants that are able to bypass the hydraulic filtration system will reduce performance
and may damage hydraulic components.
• Stand clear of the implement when starting the system for the first time after installing or servicing hydraulic
components in case a hose has not been properly connected or tightened.
ELECTRICAL SAFETY
• Always verify that power leads are connected to the correct polarity as marked. Reversing the power leads
could cause severe damage to the Raven system or other components.
• To prevent personal injury or fire, replace defective or blown fuses with only fuses of the same type and
amperage.
• Do not connect the power leads to the battery until all system components are mounted and all electrical
connections are completed.
• Always start the machine before initializing this Raven system to prevent power surges or peak voltage.
• To avoid tripping and entanglement hazards, route cables and harnesses away from walkways, steps, grab bars,
and other areas used by the operator or service personnel when operating or servicing the equipment.
TOUCH SCREEN
• Only touch the touch-screen with your finger or by using a special touch-screen stylus/pen. Operating the
touch-screen with sharp objects may cause permanent damage to the screen.
• Only clean the screen using a damp cloth. Never use caustic or other aggressive substances.
WARNING
CAUTION
Содержание RS1
