manualshive.com logo in svg

Raven AutoBoom, Калибровка и руководство по эксплуатации, Страница: 43 / 50

Поделиться
Скачать
Raven AutoBoom Скачать руководство пользователя страница 43

5

Manual No. 016-0130-076 Rev. C

39

Troubleshooting

Operation Diagnostics

TABLE 3. 

Operation Diagnostic Issues

Issue

Possible Cause

Solution

Booms raise but will not 
lower when starting the 
machine or engaging the 
hydraulics (pull-type 
sprayers) with AutoBoom 
engaged.

PWM base is too high.

Engage the AutoBoom hydraulics and allow the PWM 
base to decrease and the booms to lower 
automatically.

System is out of calibration. Re-calibrate the AutoBoom system.

(Pull-type only) Restriction 
in the tank line.

• Check the quick couplers on the sprayer.

• If the sprayer is equipped with a case drain line 

(non-restricted), connect the tank line to this hose.

Booms will not enable with 
the down-tap of the 
machine functions.

The boom sense adapter 
cables are damaged or not 
connected.

• Check the cabling.

• Use the Diagnostics screen to help determine the 

proper wiring set up.

Inadequate voltage to the 
AutoBoom system.

Use a multi-meter to 12 V is provided to the 
machine coils when the function is activated.

AutoBoom system is not 
calibrated.

Calibrate the AutoBoom system.

AutoBoom harness cable is 
damaged.

Inspect the cable for damage and repair or replace as 
necessary.

AutoBoom node is faulty.

Replace the AutoBoom node.

The pressure alarm is 
always on.

Pressure alarm setting for 
PowerGlide Plus mode is 
set too low.

Increase pressure alarm setting.

Pressure and tank hoses 
are reversed.

Check pressure (P) and tank (T) lines connected to 
AutoBoom valve and switch if necessary.

Pressure transducer is 
faulty.

• Inspect the transducer and verify the pressure 

reading on the Diagnostics screen.

• Replace the pressure transducer if necessary.

The AutoBoom harness 
cable is damaged.

Inspect the cable for damage and repair or replace as 
needed.

Booms are resting on the 
stops or cylinders are fully 
extended.

Raise the booms, lower the center section, and re-
engage AutoBoom.

Objects under one boom 
makes the opposite side 
react.

The inner and outer sensor 
connections are reversed.

Check the inner and outer sensor connections and 
reverse if necessary.

Proportional valve 
connections are reversed 
or one side is not 
connected.

Check the connections on the AutoBoom valve to 
ensure the harness cable connections are inserted 
into the correct ports.

Stability setting is too low.

Gradually increase the stability setting until the 
opposite side barely reacts to boom movement.

Proportional valve is faulty.

• Inspect the proportional valve.

• Clean and/or replace if necessary.

Содержание AutoBoom



















































Отзывы:

Нет отзывов