background image

Page 13

17.3.6  Loading the Screw (Auger)

Insert Models - Loading the Auger should only be 
carried out in OFF mode

When the stove is new or the fi re has run out of fuel, the 
auger will be empty.  In this case it may be necessary to 
‘load’ the auger so the fi re will start. 

To load the screw/auger, proceed as follows:

1.  Press Button (7) (Menu 01 “Set Clock” will appear), 

then press and hold (6) for 3 seconds.  The  display 
will show “SCREW STATE”.

2.  Use Button (1) to turn the Auger On “SCREW 1” and 

button (2) to turn it OFF.

3.  Once started auger will run for a couple of minutes 

4.  Remember to turn the screw OFF (SCREW 0) with 

button (2) before exiting, button (3)

5.  Empty the burner pot of any pellets before starting 

the fi re

Also see “17.3.4 Menu Five - Stove State (Fire Status)” 
on page 12.

17.3.7  How to synchronise the remote control with 

the fi re 

All insert stoves are fi tted with remote-control, radio-
wave handset and a receiver, located on the right-hand 
side of the stove.  Sometimes, due to interference 
from other electrical household appliances (microwave 
ovens, satellite decoders, mobile phones) the 
connection between the stove and the handset may be 
interrupted. If this happens, the following operations 
must be carried out to reinstate the connection: 

1.  Switch the power to the fi re off  at the mains switch.
2.  Press the triangle keys (1) and (2) on the remote 

together for about three seconds. The display will 
show “SCEGLI  UNITA 0”

3.  Using triangle key (2), select the unit frequency to 

be loaded (select unit 0 , 1 , 2 , 3 ) Note:  0 or 1 

are usually the best but different houses may work 
better on other settings. 

4.  Switch the power to the stove back on (if the unit 

is pulled out this will need pushing back into its 
cradle) . 

5.  Press the red button (3). 
6.  If the operation is successful, UNIT LOADED 0, 1, 2 

or 3 will appear on the remote. You may now need 
to turn the power to the stove off and back on again 
to refresh the connection with the remote.

The auger is activated

       2000

       150°

     COCLEA

  1

        ST

ATE

The auger is idle

       2000

       150°

       ST

ATE

      COCLEA

  0

Содержание Sara

























Отзывы: