background image

 

 

P/N RE - 102 / 104 Rev. No. 0 

7

 

1.5 Routine Testing

 

In order to ensure that the system is fully operational, and to comply 
with the requirements of IS 2189: 1999, the following routine attention is 
recommended: 
 
Daily - Check the panel to ascertain that it indicates normal 
operation. If any fault is indicated check that it has been recorded 
and that the appropriate actions have been taken, e.g. informing the 
maintaining company. 
Weekly - Test at least one detector or call point to confirm the 
operation of the panel and the audible alarms. Test a different zone 
each week and, if possible, a different device. Keep a record of the 
device and zone tested each week. Record and report any 
malfunction. 
Quarterly - The responsible person should ensure that every three 
months the system is checked by a competent person.  Check the 
standby batteries and the charger voltage Test at least one device in 
each zone to check the panel functions. Check the operation of the 
audible alarms and any link to a remote manned centre, Central 
Station, etc. Carry out a visual inspection of the installation to check 
for alterations or obstructions and issue a certificate of testing. 
Annually - The responsible person should ensure that, in addition to 
the quarterly checks, each device on the system is tested and that a 
visual inspection is made of the cable fittings and equipment. 
Note:  The control panel case should be cleaned periodically by 
wiping with a soft, damp cloth. Do not use any solvents. 

 
 

 
 
 
 
 
 
 
 
 
 

Содержание RE -102


































Отзывы: