background image

Page 5

GSM Cellular:

1.

 Remove security screws, top cap, and pull front of the Call Station enclosure down.

2.

 Remove the cover of the NEMA 4 enclosure mounted to the front of the Call Station enclosure. 

3.

 Locate the Cellular Module inside the enclosure.  

4.

 When the “PWR”, “RDY”, and “NW” lights on the front are illuminated, unit is ready. 

5.

 Verify SmartPhone is plugged into the FXS port on Cellular Module.

Note:

 If the SIM card is not provided to RATH® at time of purchase, an active SIM Card will need to be installed 

into SIM Card slot. When installing SIM Card, disconnect power from cellular unit, install SIM Card in SIM Card slot, 

then reapply power.

CDMA Cellular:

1.

 Remove security screws, top cap, and pull front of the Call Station enclosure down.

2.

 Remove the cover of the NEMA 4 enclosure mounted to the front of the Call Station enclosure. 

3.

 Locate the Cellular Module inside the enclosure. 

4.

 When “Power”, “Signal Strength”, and “Service Indicator” lights are illuminated solid, unit is ready.    

5.

 Verify SmartPhone is plugged into the phone port on Cellular Module.

2-Way Radio:

The 2-Way Radio phone can both transmit and receive voice communications. Our 2-Way Radios are fixed  in the 

Call Station and must be programmed to the specifics of the 2-Way System in use within the facility or campus. The 

2-Way Radio is programmed at the factory using customer provided information (frequency, squelch code, and 

narrow or wide bandwidth). The antenna is installed and tuned at the factory. Call Stations using 2-Way Radio are 

not ADA compliant (the button must be pushed and held to talk and let go to listen).

Note: 

Phones using 2-Way Radios are not programmable. Sections in this manual on Programming the Phone do 

not apply.

Adjusting the Volume for 2-Way Radio:

1.

 If the volume of the Call Station needs to be adjusted, remove security screws, top cap, and pull front  of 

    the Call Station enclosure down.

2.

 Open the NEMA 4 box to access the radio. Turn the radio volume control up or down to adjust. 

3.

 Close the NEMA 4 box.

900 MHz:

Each Call Station includes (2) 900 MHz units, (1) Remote Station, and (1) Base Station. The Remote Station  is 

already installed in the Call Station.

1.

 Locate the 900 MHz unit with Base Station labeled on the bottom.

2. 

Screw black antenna into back of 900 MHz Base Station.

3. 

Plug dedicated analog phone line or analog extension off of a PBX system into the port labeled “Line”.

4.

 Connect Power Cable included with unit into dc input on Base Station and a 120v outlet.

5.

 Test units by taking an analog phone and plugging it into the “Line” Port on Remote Station installed in     

    the Call Station. There should be a dial tone and you should be able to place a call out.

6. 

Verify SmartPhone is plugged into “Tel” Port on Remote Station. Phone is now ready for programming.

Note:

 If installing multiple 900 MHz units, please put a minimum of 3 feet between each Base Station. Connect 

one unit at a time, test, and then continue adding one unit and testing until all units are ready and functional.

Содержание 2100-CL9










Отзывы: