background image

9

Use Instructions

A. Parts list

1. Lifting Column ……................................................................................................................................. 2 pcs
2.Handset............................................................................................................................ 1 pcs
3. Control Box ……...................................................................................................................................... 1 pcs
4. Motor Cable …................................................................................................................................... 2 pcs
5. Power Cord …………............................................................................................................................... 1 pcs

Connect the cables as shown in the photo below:

B. Technical Specifications

Input: 100-240VAC
Output Power: 29VDC
Maximum accepted weight: 120 kg (including tabletop weight)
Maximum speed: 38 mm/s
Minimum height: 620mm
Travel distance: 650 mm
Operating temperature: 0-40°C
Duty Cycle: Max.10% or 2 min on and 18 min pause

Control Panel Operation and Programming Instructions

Содержание Boost Plus Single Sided Desk Workstation



















Отзывы: