background image

TRACTION DRIVE HYDROSTAT ADJUSTMENTS:  

The following adjustments must be done in order.

ADJUSTMENTS

STEP 1 - Set Neutral

Neutral is set at the factory.  If it should require 

adjustment, raise the wheels off the ground by setting 

the machine on jackstands or blocks.  Disconnect 

the  control rod 

A

 at each pump end. Loosen bolt 

S

 securing the neutral plate eccentric shaft just 

enough to turn the shaft.  Start the engine and run 

at low speed.  Turn eccentric shaft 

T

 to raise or 

lower the point at which the follower bearing is held 

in the center of the “

V

” until the wheels stop turning.  

Tighten the eccentric shaft bolt.  Increase the throttle 

setting and check the adjustment.  Readjust if 

necessary.  Shut the engine off before proceeding to 

step 2.

STEP 2 - Adjust Control Rods

First adjust neutral, as outlined in Step 1.  Set control 

levers to neutral.  Adjust swivels 

B

 on lower ends of 

control rods 

A

 so they just go into the holes on the 

pump arm control plates. 

After adjusting swivel 

B

 on left side, tighten jam nut 

C

.

Содержание 36 HYDRO Z-CONTROL MID-16HP KAW SIDE DISCHARGE SELF PROPELLED WALK BEHIND MOWER





























Отзывы: