CP-06-01
1 3
1 3
1 3
1 3
1 3
MicroPak Controller - Installation
Discreet I/O Board Dipswitch
Discreet I/O Board Dipswitch
Discreet I/O Board Dipswitch
Discreet I/O Board Dipswitch
Discreet I/O Board Dipswitch
SW2-1
SW2-1
SW2-1
SW2-1
SW2-1
This dipswitch is set according to the cascade in
use with the MicroPak Control Unit. It is factory set
to the ON position for use with the HP404 FM
cascade in the Evolver applicator.
T
T
T
T
Table 1 - Electrical I/O
able 1 - Electrical I/O
able 1 - Electrical I/O
able 1 - Electrical I/O
able 1 - Electrical I/O
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
W A R N I N G
>
Dipswitch SW3-3 should never be set
to OFF while the remote Ready input is
active or high voltage will be on all of the
time (whenever AC power is on).
!!!!!
DIP SWITCH SUMMARY
DIP SWITCH SUMMARY
DIP SWITCH SUMMARY
DIP SWITCH SUMMARY
DIP SWITCH SUMMARY
(See Figure 6A & 6B)
(See Figure 6A & 6B)
(See Figure 6A & 6B)
(See Figure 6A & 6B)
(See Figure 6A & 6B)
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
Dipswitch SW3-1
Dipswitch SW3-1
Dipswitch SW3-1
Dipswitch SW3-1
Dipswitch SW3-1
In remote mode, determines whether over-current
setpoint control is provided by the remote Over-
current Setpoint analog input or from R21 of the
MicroPak process board. If dipswitch SW3-1 is
ON control is from the remote analog input. If
dipswitch SW3-1 is OFF control is from
potentiometer R21.
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
MicroPak Process Board
Dipswitch SW3-3
Dipswitch SW3-3
Dipswitch SW3-3
Dipswitch SW3-3
Dipswitch SW3-3
Determines whether high voltage is enabled when
ready mode is active. If dipswitch SW3-3 is ON,
high voltage is NOT
NOT
NOT
NOT
NOT enabled in ready mode.
Therefore, separate ready and high voltage enable
signals are required to enable high voltage. This is
the typical setting for remote mode. If dipswitch
SW3-3 is OFF, high voltage IS
IS
IS
IS
IS enabled when
ready mode becomes active. This is the typical
setting for local (manual) mode, so that pushing the
High Voltage Enable Switch to the ON position will
enable high voltage output without requiring a ready
signal.
Inputs:
P3 Terminal
Inputs:
P3 Terminal
kV Setpoint (0-10VDC)
C4
kV Setpoint (0-10VDC)
C8
Over-current Setpoint (0-10VDC)
C3
Over-current Setpoint (0-10VDC)
C7
High Voltage Reset (24VDC)
C2
High Voltage Reset (24VDC)
C6
High Voltage On (24VDC)
C1
High Voltage On (24VDC)
C5
Ready
A1
Ready
A5
Outputs:
Outputs:
Overload (24VDC)
B4
Overload (24VDC)
B8
HV Ready (24VDC)
B3
HV Ready (24VDC)
B7
HV On (24VDC)
B2
HV On (24VDC)
B6
Interlock:
Interlock:
Interlock Line A
A3
Interlock Line A
A7
Other:
Other:
Ground
B1
Ground
B5
Ground
A2
Ground
A6
MicroPak 1
MicroPak 2
Содержание MICROPAK A11789
Страница 2: ...CP 06 01 ...
Страница 33: ...CP 06 01 30 30 30 30 30 MicroPak Controller Parts Identification NOTES NOTES NOTES NOTES NOTES ...
Страница 35: ...CP 06 01 ...