background image

 

Positive Displacement Pump - Safety 

LN-9415-01 

AREA 

Tells where haz-
ards may occur. 

HAZARD 

Tells what the hazard is. 

SAFEGUARDS 

Tells how to avoid the hazard. 

Spray Area 

Fire Hazard 

Improper  or  inadequate  opera-
tion  and  maintenance  proce-
dures will cause a fire hazard. 

Protection    against    inadvertent 
arcing that is capable of causing 
fire  or  explosion  is  lost  if  any 
safety  interlocks    are    disabled  
during operation. Frequent Pow-
er  Supply  or  Controller  shut-
down indicates a problem in the 
system requiring correction. 

Fire  extinguishing  equipment  must  be  present  in 
the spray area and tested periodically. 

Spray areas must be kept clean to prevent the ac-
cumulation of combustible residues.  

Smoking must never be allowed in the spray area. 

The high voltage supplied to the atomizer must be 
turned  off  prior  to  cleaning,  flushing  or  mainte-
nance. 

When using solvents for cleaning: 

• 

Those  used  for  equipment  flushing  should 
have flash points equal to or higher than those 
of the coating material. 

• 

Those solvents used for general cleaning must 
have  a  flash  point  at  minimum  of  5°C  (9°F) 
greater than the ambient temperature.  It is the 
end users responsibility to insure this condition 
is met. 

• 

Spray  booth  ventilation  must  be  kept  at  the 
rates  required  by  NFPA-33,  OSHA,  country, 
and  local  codes.    In  addition,  ventilation  must  
be    maintained    during  cleaning  operations 
using flammable or combustible solvents. 

Electrostatic  arcing  must  be  prevented.    Safe 
sparking distance must be maintained between the 
parts being coated and the applicator.  A distance 
of  1  inch  for  every  10KV  of  output  voltage  is  re-
quired at all times. 

Test only in areas free of combustible material. 

Testing may require high voltage to be on, but only 
as instructed. 

Non-factory    replacement    parts    or    unauthorized 
equipment modifications may cause fire or injury. 

If  used,  the  key  switch  bypass  is  intended  for  use 
only  during  setup  operations.  Production  should 
never be done with safety interlocks disabled. 

Never  use  equipment  intended  for  use  in  water-
borne  installations  to  spray  solvent  based  materi-
als. 

The paint process and equipment should be set up 
and  operated  in  accordance  with  NFPA-33,  NEC, 
OSHA,  local,  country,  and  European  Health  and 
Safety Norms. 

Содержание A13619-00























Отзывы: