background image

10

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

Electrical Connections

This appliance must be installed by a qualified electrician 
to comply with the relevant Institute of Electrical 
Engineers (I.E.E.) regulations and also the local electricity 
supply company requirements.

 

WARNING: THIS APPLIANCE MUST BE EARTHED

Note: All external wiring must comply with the IEE 
Regulations for the Electrical Equipment of Buildings. 
Connection to the electrical supply can be made with either 
a plug and socket, or be permanently wired via a double pole 
switch. The hob is supplied with a 3-core cable, 900mm long.

If a replacement cable is fitted it must be 250V high 
temperature PVC (85°C), 1 mm²

 

minimum conductor size.

Plug Connection

For a plug connection a three-pin plug to BS 1363 with a 
capacity of not less than 13A must be used and fitted with a 
3A fuse, ‘ASTA’ approved to BS 1362.

After replacing the fuse the cover must be refitted. If the 
cover is lost, the plug must not be used until a replacement 
cover has been obtained from your supplier. The colour of the 
correct fuse carrier is that of the coloured insert in the base of 
the fuse recess, or stated elsewhere on the plug. Always state 
this colour when ordering a replacement fuse carrier.

IMPORTANT:

 The wires in the mains lead are coloured in 

accordance with the following code:

Green and yellow:  Earth

Blue: 

Neutral

Brown: 

Live

Hotplate

Check each burner in turn. There is a spark ignition system 
that works when the knob is pressed in. Each burner also has 
a special safety device that stops the flow of gas if the flame 
goes out. 

Push in and turn a control knob to the large flame symbol [

ArtNo.030-0012 - RG70 symbols

].

Keep holding the knob pressed in to let the gas through to 
the burner for few seconds. The igniter should spark and light 
the gas.

If, when you let go of the control knob, the burner goes out, 
the safety device has not held in. Turn the control to the 
OFF position and wait one minute, then try again this time 
holding in the control knob for slightly longer.

Customer Care

Please complete your contact details in the front of this 
section. Please inform the user how to operate the hotplate 
and hand over the instruction pack.

Thank you.

ArtNo.317-0012 - Hob fittings 1

�������

�������

���������

�����

������

�������

���

�������

���������

�����

���

�����

�����

Fig.5-4

Содержание RGG60





















Отзывы: