Rangemaster Kitchener 90 Electric, Инструкция по установке и эксплуатации, Страница: 28 / 36

28
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
lead. Fit new electrode to the lead. Fix electrode in
burner with screw. Replace burner cap. Check the burner
ignition. Replace pan supports.
11. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
The burners except the right hand wok burner
are mounted on support struts. For these burners,
disconnect the burner feed pipes at the burner. Remove
the screws at the front and rear holding the support
struts. Lift the strut and burners clear. The burners are
fixed to the support struts with 2 screws. Remove the
appropriate burner and fit the new one. Reassemble in
reverse order. Check burner operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.
12. To Remove an Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free.
Door is heavy - take care. Open the oven door. Loosen
the two top hinge screws.
Support the weight of the door and remove the screw
nearest the hinge pin. Swing the hinge up and away
from the hinge pin on the door.
Lift the door away from the bottom hinge.
Re-assemble in reverse order.
When replacing the door ensure that the nylon hinge
bush is in position between the hinge pin and the hinge
bracket at the both the bottom and top.
13. To Change Main Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fixing screws from the door sides (two each side).
thermostat capillary
earthing plate
Right hand oven,
The oven thermostat capillary is clamped to the right
hand rear upright with an earthing plate.
Remove thermostat phial cover (2 screws). Unclip the
thermostat phial from the clips in the oven back.
Feed the thermostat capillary out of the oven.
Disconnect wiring from thermostat. Remove 2 screws
holding thermostat to mounting panel. Fit new
thermostat and reassemble in reverse order. Ensure
that the phial is clipped to the oven back with the phial
centrally positioned between the clips.
Remember to refit the earthing plate.
Check operation of thermostat.
7. To Change Grill Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Disconnect wiring from controller. Remove 2 screws
holding controller to mounting panel. Fit new controller
and reassemble in reverse order. Check for correct
operation.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS
TURN OFF GAS SUPPLY.
8. To Change Hotplate Control Taps
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Undo compression fitting at the rear of the tap. Remove
the fixings that secure the tap to the gas rail. Remove
the tap. Remove and discard the gasket seal. Fit new
gasket seal to replacement tap. Re-assemble in reverse
order. Check the appliance is gas sound. Check hotplate
ignition.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance is
gas sound.
10. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically
up sufficiently to grip the lead between thumb and
forefinger. Pull off the electrode, but keep hold of the