background image

 

EcoPro 

Range Road Enterprises Ltd 
Box 944 
Eckville AB T0M 0X0 
www.range-road.ca

 

 

Page 6 

 
 

Component Identification  

 

   

 

1.

 

2” Coupler:

 Attaches the firewood processor to your ATV or vehicle. Fits only 2” hitch balls. 

2.

 

Safety Chains: 

for attaching to tow vehicle along with 2” coupler. 

3.

 

Front Wheel: 

Used for moving on even stable ground & raising or lowering coupler height.

 

4.

 

Leg:

 The leg helps support the firewood processor while operating. The leg should be pulled out of the 

sleeve and reinserted from top down while towing (see Operation Instructions) 

5.

 

Engine:

 The air cooled engine powers the hydraulic pump. 

6.

 

Hydraulic Cylinder: 

The hydraulic cylinder has a 61cm (24”) stroke. It is rated to 3500 PSI 

7.

 

Gear Pump:

 The gear pump makes the hydraulic oil flow through the system. The EcoPro has a 2 section 

pump with one live section dedicated to the saw/ram and one dedicated to the conveyor/accessories. 

8.

 

Hydraulic Filler Cap: 

Unscrew  the  cap  to  add  hydraulic  oil  to  the  tank,  oil  should  be  midway  up  the 

siteglass 

9.

 

Tires:

 Maximum rated speed is:        12” Wheels - 80Kph (50 Mph). 

10.

 

Log Deck:

 The log deck is angled to help keep the log against the deck wall without operator assistance. 

 
 
 

Содержание EcoPro Series



















Отзывы: