Rane TTM57mkII, Руководство пользователя

Страница: 10 / 36

OWNER’S MANUAL
10
TTM57mkII
Audio Connections
Analog Inputs
Two Phono / CD inputs may each be set for
PH
or
CD
using the rear panel buttons,
in
for a turntable and
out
for a CD deck. Two more RCA
Aux
inputs are provided, one for each input channel. This configuration
allows you to connect the Aux inputs to a pair of CD decks, while the PH/CD inputs connect to a pair of
turntables or two more CD decks. Connect your turntable ground wires to the
PHONO GROUNDS
posts
when using
PH
inputs.
One stereo Session Input is on a pair of RCA input jacks. This input may connect two mixers together or
as a general purpose auxiliary input to the mixer.
The Mic Input will accept an XLR 3-pin plug, a balanced ¼" TRS (tip-ring-sleeve) plug or an unbalanced
TS (tip-sleeve) plug. This input may be set for Microphone or Line level using the
MIC - LINE
button on the
rear panel. Set this to Line (button out) when connecting a wireless receiver.
A stereo FlexFX Loop Return input is on unbalanced RCA jacks. The FlexFX Return input is normally
used along with the FlexFX Send output to connect an outboard analog effects processor.
Phono Sensitivity can be adjusted in the "Deck Inputs 1-2 Control Panel" on page 20.
Analog Outputs
There are five stereo analog outputs available on the mixer:
•
MAIN OUT
is on a pair of balanced XLR jacks with pin 2 “hot” per AES standards.
•
BOOTH OUT
is on a pair of balanced ¼" TRS jacks.
•
SESSION OUT
is available on a pair of unbalanced RCA jacks.
•
FLEXFX LOOP SEND
output is available on a pair of unbalanced RCA jacks. The FlexFX Send output is
normally used along with the
FLEXFX LOOP RETURN
input to connect outboard effects. The +4 / -10
switch changes the send level for your effects device. Typically, RCA connections prefer the -10 setting,
and ¼" devices may sound better with the +4 setting. Consult your effects device manual.
The Main, Booth and Session outputs arrive from the same “Main Mix” signal. Main, Booth and Session
outputs each have their own
LEVEL
control. Because all signals are identical, you may use any of these
outputs as the “Main” output if a different cable type is required for system connection.
Rane recommends balanced wiring for the strongest signal and rejection of hum and noise. If your
cable to the destination is less than 10 feet (3 meters), you can often get away with an unbalanced cable.
See the RaneNote “
Sound System Interconnection ” at rane.com for cable wiring recommendations.
Power Supply
This mixer features an internal universal switching power supply that operates on any AC mains 100 to
240 VAC, 50 or 60 Hz (most places in the world). The universal supply is a major plus for the traveling DJ,
who only needs the right IEC line cord, available from a local electronics store. Though this mixer has turn
on/off muting, it’s smart to leave the power unplugged until everything else is connected.
BOOTH
PHONO
GROUNDS
SEND RETURN
DECK 1 DECK 2 SESSION
100-240V 50/60 Hz 15 WATTS
RANE CORPORATION
OUT IN
AUX PH / CD AUX PH / CD
MIC
FlexFX LOOP
USB
MAIN OUT
B A
RIGHT LEFT
MIC
LINE
PH
CD
-10
+4
PH
CD
! !
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B)