R&S NGE-K101 страница 94 Скачать руководство пользователя

Страница: 94 / 105

Remote Control

R&S

NGE100B

User Manual 5601.1343.02 ─ 02

ARBitrary:REPetitions

This command defines or queries the repetition of the defined arbitrary waveform for
channel 1.

Note: If the repetition is set to "0", the arbitrary waveform repeats continuously.

Parameters:

0..255

Example:

ARB:REP 10

Set the repetition rate of the defined arbitrary waveform as 10.

ARB:REP? -> 10

Return the defined repetition rate of the selected channel.

ARBitrary:POINts?

This command returns the number of arbitrary points of EasyArb waveform.

Return values:

<arg0>

Usage:

Query only

ARBitrary[:STATe]

<arg0>

This command activates/deactivates or queries the EasyArb state. ON: Ch 1 is ready
to run arb waveform.

Parameters:

<arg0>

ARBitrary:SAV

<arg0>

This command saves EasyArb settings and previous defined arbitrary points into the
respective memory locations M1-M5.

Parameters:

<arg0>

Range:

0..4

Example:

INST 1
ARB:DATA 10,1,0,5,0
ARB:REP 10
ARB:SAV 1

Usage:

Setting only

ARBitrary:STARt

This command starts the previous transferred EasyArb waveform in channel 1 if Easy-
Arb is enabled.

Usage:

Event

Remote Control - Commands

www.allice.de

Allice Messtechnik GmbH

Содержание NGE-K101










































































































Результаты поиска

Содержание NGE-K101

Отзывы:

Похожие инструкции для NGE-K101

Бренды по названию

Популярные бренды

R&S NGE-K101, Руководство пользователя

Результаты поиска

Содержание NGE-K101

Отзывы:

Похожие инструкции для NGE-K101

Бренды по названию

Популярные бренды