R&S 1424.7005.02 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 514

background image

Sensor Configuration

R&S

®

NRX

116

User Manual 1178.5566.02 ─ 07

"2"

Lower sampling rate
Recommended to avoid measurement errors caused due to aliasing
effects. However, this setting extends the measurement time.

Remote command:

CALCulate<Measurement>[:CHANnel<Channel>]:SAMPling

Smoothing

Available for continuous average measurements.

Enables or disables the smoothing filter, a steep-edge digital lowpass filter. The filter
reduces result fluctuations caused by modulation.

"Off"

If the modulation frequency is known, set the

time exactly to

an integer multiple of the modulation period and disable smoothing.
Otherwise, the modulation can have a considerable influence, even if
the sampling window is much larger than the modulation period.
300 to 3000 periods are required to obtain the same effect as with
smoothing enabled. The sampling values are considered equivalent
and are averaged in a sampling window, which yields an integrating
behavior of the measuring instrument.

"On"

If the modulation period varies or is not precisely known, enable
smoothing.
The selected sampling window has to be 5 to 9 times larger than the
modulation period so that the fluctuations caused by modulation are
sufficiently reduced. The sampling values are subjected to weighting
(raised-von-Hann window), which corresponds to video filtering.

Remote command:

CALCulate<Measurement>[:CHANnel<Channel>][:POWer][:AVG]:
SMOothing[:STATe]

Dropout Tolerance

Available for burst average measurements.

Detects the falling edge of a burst. If the power keeps low for at least the set time, the
end of the burst is assumed. Modulation-specific power drops that are shorter than the
set value are ignored.

Remote command:

CALCulate<Measurement>[:CHANnel<Channel>][:POWer]:BURSt:
DTOLerance

Exclude from Start, Exclude from End

Available for burst average measurements.

Sets the time interval at the beginning or end of bursts that is excluded from the mea-
surement. Thus, signal overshoots are omitted.

Remote command:

CALCulate<Measurement>[:CHANnel<Channel>]:BURSt:TIMing:EXCLude:
STARt

CALCulate<Measurement>[:CHANnel<Channel>]:BURSt:TIMing:EXCLude:
STOP

Mode Settings

www.allice.de

Allice Messtechnik GmbH

«
...
114
115
116
117
118
...
»

Содержание 1424.7005.02



































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1424.7005.02

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: Elcontrol Страницы: 7

VX200-N-VI Series

Бренд: XS Scuba Страницы: 34

FlowStar2 LB 514

Бренд: BERTHOLD TECHNOLOGIES Страницы: 130

Бренд: Megger Страницы: 8

Бренд: Endress+Hauser Страницы: 24

Friendly Digital Piano Forte PV35

Бренд: Kawai Страницы: 102

Бренд: Z-Wave Страницы: 5

Бренд: Klein Tools Страницы: 20

Бренд: Agilent Technologies Страницы: 20

A570 Ambient Monitor

Бренд: iDigit Страницы: 15

PA 900 Musikant

Бренд: Korg Страницы: 20

Бренд: R.M. Young Страницы: 11

InnovaSonic 205i

Бренд: Sierra Страницы: 12

Бренд: Wetekom Страницы: 34

Бренд: Zenner Страницы: 4

Бренд: Reed Instruments Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды