Page
10
of
14
AB0044
R&G
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Email:
•
Placer 2 rondelles M10 (article 11) sur 2 boulons M10 (article 10), voir photo 13, puis placer les
boulons dans le support de fixation inférieur de la barre aventure du côté droit (article 8) voir photo 13.
•
Placer 2 petites entretoises (article 12) sur l’extrémité des boulons, voir photo 13.
•
Monter l’ensemble en position de façon à ce que le support de fixation supérieur se place sur l’axe
moteur, voir photo 12.
•
Placer 2 boulons de fixation inférieurs dans le membre du cadre puis dans les trous filetés comme à
l’origine (Ne pas trop serrer pour le moment).
•
Placer les 2 boulons de fixation inférieurs dans le membre du cadre puis dans les trous filetés comme à
l’origine (ne pas trop serrer pour le moment).
•
Placer une des rondelles M12 (article 5) et un écrou M12 (article 4) sur l’axe moteur puis engager
complètement l’écrou mais ne pas serrer pour le moment.
•
Serrer les 2 écrous M12 en laissant des longueurs équivalentes dépasser de chaque côté à travers les
écrous.
•
Serrer les 4 boulons M10.
•
Insérer les 2 cache écrou (article 2) sur les 2 écrous M12 supérieurs.
•
Insérer les 4 boulons M10 (article 9) sur les boulons inférieurs.
•
Insérer les 4 inserts tubulaires (article 3) dans les extrémités ouvertes des 2 Barres Aventure.
•
Enlever la prise et le bloc de bois.
•
Remonter le ventre de carénage comme à l’origine.
ISSUE 1 13/11/2018 (NSY)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes
which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer
acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s
order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular
purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of
charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not
affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the
purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s
or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and
subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and
otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do
not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at
the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless
within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.