RAMSET T2 Скачать руководство пользователя страница 2

SAFETY INTRODUCTION 

DANGER

SAFETY INTRODUCTION 

DANGER

2

!

  Read, understand and follow the instructions in  

the tool manual before attempting to use the tool.

!

  Operators and Bystanders must wear eye and  

hearing protection.

!

  Never close tool with hand over the fastener loading 

end of the tool. A serious hand injury from penetration 
by the piston or fastener could result.

!

  The gas in fuel cells is under pressure and the gas  

is flammable.

!

  Do not open, puncture or burn fuel cells.

!

  Store fuel cells in a well ventilated area, at temperatures 

below 50° C (122° F) and out of the sunlight.

!

  Keep fuel cells away from flames, sparks and heat.

!

  Do not attempt to recharge, refill or recycle fuel cells.

!

  Never operate the T2 tool if flammable or explosive 

materials are nearby.

 

Just as no one can merely read a book about driving an automobile and then hope  
to drive one safely, no one should attempt to use the T2 gas powered tool without  
adequate, competent personal instruction. 

No automobile instruction book or instructor can forewarn a learner against all possibilities  
and emergencies, nor can printed material detail all possible conditions surrounding the 
use of Ramset tools and products.

Responsibility for the safe and proper use of this tool rests with the tool user 
and the employer.

DANGER

THIS TOOL IS TO BE USED ONLY BY PROPERLY TRAINED  

OPERATORS. ATTEMPTING TO HANDLE OR OPERATE THE T2 GAS  

POWERED TOOL WITHOUT PROPER TRAINING CAN RESULT  

IN SERIOUS INJURY TO THE OPERATOR OR BYSTANDERS.

DANGER

Содержание T2

















Отзывы: