RAMSET T2 Скачать руководство пользователя страница 15

Ramset warranty that new T2 power  
fastening tools, parts and accessories 
will be free from defects in material  
and workmanship for the period shown 
below, after the date of delivery to the 
original user.

TWO-YEAR WARRANTY

A two-year warranty will apply to  
all parts, except those listed below  
as normal wearing parts, or parts  
which are specifically covered by  
an extended warranty.

SIX-MONTH WARRANTY

A six-month warranty applies to the  
following parts, which are considered 
normal wearing parts:

• Bumper
• Piston Assembly
• O-Rings
• Piston Rings

WARRANTY STATEMENT

Ramset’s sole liability hereunder will be 
to replace any part or accessory which 
proves to be defective within the specific 
time period. Any replacement part or 
accessory provided in accordance with 
this warranty will carry a warranty for 
the balance of the period of warranty 
applicable to the part it replaces.  
This warranty does not apply to part  
replacement required due to normal 
wear.

This warranty is void as to any tool 
which has been subjected to misuse, 
abuse, accidental or intentional damage, 
use with fasteners, fuel, battery, or battery  
chargers not meeting Ramset specification,  
size, or quality, improperly maintained, 
repaired with other than genuine T2 
replacement parts, damaged in transit  
or handling, or which, in Ramset’s 
opinion, has been altered or repaired in 
a way that affects or detracts from the 
performance of the tool.

RAMSET MAKES NO WARRANTY, 
EXPRESSED OR IMPLIED, RELATING 
TO MERCHANTABILITY, FITNESS, OR 
OTHERWISE, EXCEPT AS STATED 
ABOVE and the liability AS STATED 
ABOVE AND AS ASSUMED ABOVE  
is in lieu of all other warranties arising 
out of, or in connection with, the use 
and performance of the tool, except  
to the extent otherwise provided by 
applicable law.

RAMSET SHALL IN NO EVENT BE 
LIABLE FOR ANY DIRECT, INDIRECT,  
OR CONSEQUENTIAL DAMAGES, 
INCLUDING, BUT NOT LIMITED TO  
DAMAGES WHICH MAY ARISE FROM 
LOSS OF ANTICIPATED PROFITS 
OR PRODUCTION, SPOILAGE OF 
MATERIALS, INCREASED COST OF 
OPERATION OR OTHERWISE.

Ramset reserves the right to change 
specifications, equipment, or designs  
at any time without notice and without 
incurring obligation.

 

WARRANTY 

 

WARRANTY 

 

15

T2 TOOL WARRANTY AND LIMITATIONS

Содержание T2

















Отзывы: