manualshive.com logo in svg

RAMSET RT400 M, Инструкция по безопасности и эксплуатации оператора

Поделиться
Скачать
RAMSET RT400 M Скачать руководство пользователя страница 18

WARRANTY

ALL WARRANTIES OF THE PRODUCTS DESCRIBED HEREIN, EXPRESSED
OR IMPLIED, INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSES, ARE SPECIFICALLY EXCLUDED,
EXCEPT FOR THE FOLLOWING:

Ramset will repair or replace, at its sole

option, any tool, part, or fastener which, within 5 years after sale by Ramset 
is found by Ramset to be defective in material or workmanship, normal wear
and tear excluded. 

THIS IS THE SOLE WARRANTY OF RAMSET AND THE

SOLE REMEDY AVAILABLE TO THE BUYER AND IN NO EVENT WILL ANY
DIRECT OR INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR
ANY OTHER DAMAGES, BE AVAILABLE.

Copyright 2005 ITW Ramset/Red Head

POWDER ACTUATED TOOL

MANUFACTURES' INSTITUTE INC.

TM

Concrete Fastening Systems

Wood Dale, IL 60191

630-350-0370

www.ramset-redhead.com

Buy with Confidence...

Buy From Your Authorized Distributor

© ILLINOIS TOOL WORKS 2005

PRINTED IN THE U.S.A. 

REVISED 01/05

Form No. SMRT400A-01/05

THE MODEL RT400 TOOL COMPLIES WITH OSHA REQUIREMENTS 

AND WITH ANSI A10.3 SPECIFICATIONS

FOR TOOL REPAIR SERVICE CONTACT YOUR LOCAL

AUTHORIZED ITW RAMSET/RED HEAD DISTRIBUTOR OR CONTACT

YOUR NEAREST RAMSET TOOL REPAIR CENTER

WEST

MIDWEST

EAST

Los Angeles, CA

Paris, KY

Allentown, PA

5950 Boxford

7000 Bypass Road

739 Roble Road

Commerce, CA 90040

Paris, KY 40361

Allentown,PA 18109

Phone: 800-368-9724 (CA only)

Phone: 800-816-6645

Phone: 800-266-9723

Phone: 800-227-1823

Fax: 800-816-6673

Fax: 610-266-0962

Fax: 800-253-6444

Содержание RT400 M



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды