manualshive.com logo in svg

RAMSET RT400 M, Инструкция по безопасности и эксплуатации оператора

Поделиться
Скачать
RAMSET RT400 M Скачать руководство пользователя страница 14

Always make sure the tool is not loaded before performing any service or repair and
always wear safety goggles when cleaning or servicing the tool.

NORMAL CLEANING

All front end parts shown in the disassembly section are to be cleaned daily with a good
detergent oil and wire brush. Remove all dirt and carbon buildup and wipe parts dry with 
a clean rag. Check all parts for wear or damage before reassembly and replace or repair
any worn or damaged parts.

COMPLETE CLEANING / GENERAL MAINTENANCE

Heavy or constant exposure to dirt and debris may require that the tool be cleaned more
extensively. Complete disassembly and cleaning of all parts may be necessary to restore
the tool to normal operation. General maintenance should be performed every six months
or more often if the tool is subjected to heavy use. Contact your authorized Ramset
Distributor for assistance.

IMPROPERLY MAINTAINED TOOLS CAN CAUSE SERIOUS INJURIES 

TO TOOL OPERATOR AND BYSTANDERS

CLEAN TOOL DAILY

ALWAYS FUNCTION TEST THE TOOL AFTER PERFORMING ANY

SERVICE. SEE PAGE 9 FOR DETAILS ON THE FUNCTION TEST.

MAGAZINE SCHEMATIC / MAINTENANCE

MAGAZINE SCHEMATIC / MAINTENANCE

14

MAINTENANCE

RT400 TOOL MAGAZINE SCHEMATIC AND PARTS LIST

KEY

PART NO.

DESCRIPTION

1M

A1011A

MUZZLE ASSEMBLY

2M

A1077A

LOCKOUT ASSEMBLY

3M

A1013

MAGAZINE HOUSING

4M

A1021A

SPRING BLOCK ASSEMBLY

5M

A1014A

MAGAZINE SLIDER/

FOLLOWER ASSEMBLY

Содержание RT400 M



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды