background image

ITW Ramset/Red Head warranty that
new R150 power fastening tools, parts
and accessories will be free from
defects in material and workmanship 
for the period shown below, after the
date of delivery to the original user.

TWO-YEAR WARRANTY

A two-year warranty will apply to 
all parts, except those listed below 
as normal wearing parts, or parts 
which are specifically covered by 
an extended warranty.

SIX-MONTH WARRANTY

A six-month warranty applies to the 
following parts, which are considered
normal wearing parts:

• Bumper

• Piston Assembly

• O-Rings

• Piston Rings

WARRANTY STATEMENT

ITW Ramset/Red Head’s sole liability
hereunder will be to replace any part or
accessory which proves to be defective
within the specific time period. Any
replacement part or accessory provided
in accordance with this warranty will
carry a warranty for the balance of the
period of warranty applicable to the part
it replaces. This warranty does not apply
to part replacement required due to 
normal wear.

This warranty is void as to any tool which
has been subjected to misuse, abuse,
accidental or intentional damage, use with
fasteners, fuel, battery, or battery chargers
not meeting ITW Ramset/Red Head
specification, size, or quality, improperly
maintained, repaired with other than
genuine R150 replacement parts,
damaged in transit or handling, or which,
in ITW Ramset/Red Head’s opinion, has
been altered or repaired in a way that
affects or detracts from the performance
of the tool.

ITW RAMSET/ RED HEAD MAKES NO
WARRANTY, EXPRESSED OR IMPLIED,
RELATING TO  MERCHANTABILITY,
FITNESS, OR OTHERWISE, EXCEPT 
AS STATED ABOVE and the liability 
AS STATED ABOVE AND AS ASSUMED
ABOVE is in lieu of all other warranties
arising out of, or in connection with, the
use and performance of the tool, except
to the extent otherwise provided by
applicable law.

ITW RAMSET/RED HEAD SHALL IN 
NO EVENT BE LIABLE FOR ANY
DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED
TO DAMAGES WHICH MAY ARISE FROM
LOSS OF ANTICIPATED PROFITS OR
PRODUCTION, SPOILAGE OF MATERIALS,
INCREASED COST OF OPERATION OR
OTHERWISE.

ITW Ramset/Red Head reserves the right
to change specifications, equipment, or
designs at any time without notice and
without incurring obligation.

WARRANTY

WARRANTY

15

R150 TOOL WARRANTY AND LIMITATIONS

Содержание R150

















Отзывы: