RAMSET CBAGR18, Руководство пользователя

Страница: 14 / 20

Angle Grinder 18V Owners Manual
- 014 -
30 | English
1 609 92A 47F | (14.11.17) Bosch Power Tools
Approved
Abrasive
Tools
The permissible speed [min
-1
] or the circumferential speed
[m/s] of the grinding tools used must at least match the values
given in the table.
Therefore, observe the permissible rotational/circumferen-
tial speed on the label of the grinding tool.
Rotating the Machine Head

Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
The machine head can be
rotated with respect to
the machine housing in
90° steps. In this man-
ner, the On/Off switch
can be brought into a
more convenient position
for special working situa-
tions, e.g. for left-handed
persons.
Completely unscrew the
four screws. Rotate the
machine head carefully, without removing it from the hous-
ing, to the new position. Screw in and tighten the four screws
again.
Dust/Chip Extraction

Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Avoid
dust accumulation at the workplace. Dust can
easily ignite.
Operation
Start -up
Inserting the battery
Insert the charged battery
8
from the front into the base of the
power tool until the battery is securely locked.
Switching On and Off
To start the power tool, push the On/Off switch 4 forwards.
To lock the On/Off switch 4 , press the On/Off switch 4 down
at the front until it latches.
To switch off the power tool, release the On/Off switch 4 or,
if it is locked, briefly push down the back of the On/Off switch
4 and then release it.
To save energy, only switch the power tool on when using it.

Check
abrasive
tools before using. The
abrasive
tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grinding
tools. Damaged grinding tools can burst and cause injuries.
Kickback stop
If there is a sudden kickback in the power
tool, e. g. jamming in a separating cut, the
power supply to the motor will be interrupt-
ed electronically.
To restart the operation, switch the On/Off switch 4 to the
Off position and start the machine again.
Restart Protection
The restarting protection feature prevents uncontrolled restart-
ing of the machine after an interruption in the power supply .
To restart the operation, switch the On/Off switch
4
to the
Off position and start the machine again.
Impact shutdown
The integrated impact shutdown switches the power tool off
as soon as it hits the floor. T
To restart the operation, switch the On/Off switch
4 to the
Off position and start the machine again.
max.
[mm] [mm]
D b d [min -1 ] [m/s]
115
125
22.2
22.2
9000
9000
80
80
115
125
–
–
9000
9000
80
80
75 30 M 14 9000 45
82 – M 14 9000 80
D
D
b
d
D
d
OBJ_BUCH-3456-001.book Page 30 Tuesday, November 14, 2017 1:42 PM
–
–
7
7