background image

 

 

 

III OPERATION 
 

 

SHUT-OFF PROCEDURE – GASOLINE ENGINE

 

 

1.

 

Park  the  Mini-Skid  on  level  ground.  
If  it  is  necessary  to  park  on  a  slope, 
park  across  the  grade  and  block  the 
wheels. 

2.

 

Lower  the  lift  arms  and  ground  the 
bucket. 

3.

 

Return  throttle  control  to  “idle” 
position, and allow engine to idle for 
a short while. 

4.

 

Ensure  Auxiliary  &  Control  levers 
are in neutral position. 

5.

 

Turn  ignition  key  off,  and  remove 
key. 

 

IMPORTANT 

Be Sure Ignition Key Is In OFF Position 

Or Even Removed When The Engine Is 

Not Running.

 

 

 

STARTING PROCEDURE – DIESEL ENGINE 

 

1.

 

Move  fuel  shut-off  forward  to  the 
“On” position. 

2.

 

Open Throttle lever slightly. 

3.

 

Turn  key  clockwise  to  the  first, 
“Preheat Position and hold for a few 
seconds. 

4.

 

Turn  key  further  clockwise  to  the 
“Start” position to crank engine. 

5.

 

Once engine starts, release key. 

 

6.

 

Set  throttle  lever  to  idling  speed  to 
allow engine to warm up. 

7.

 

If  engine  fails  to  start  after  cranking 
10  seconds,  repeat  steps  3  and  4, 
allowing a longer “Preheat” period 

8.

 

To restart a warm engine, move fuel 
shut-off  to  the  “On”  position  and 
turn key to start. 

 

SHUT-OFF PROCEDURE – DIESEL ENGINE

1.

 

Park  the  Mini-Skid  on  level  ground.  
If  it  is  necessary  to  park  on  a  slope, 
park  across  the  grade  and  block  the 
wheels. 

2.

 

Lower  the  lift  arms  and  ground  the 
bucket. 

3.

 

Move  throttle  to  a  slow  idling 
position  and  allow  the  engine  to  run 
for a few minutes to cool down. 

4.

 

Pull  fuel  shut-off  knob  back  to  the 
“Off” position to stop engine. 

5.

 

Turn  key  counter  –  clockwise  to  the 
“Off”  position. 

 
 
 
 
 

 

Содержание 950


































Отзывы:

Похожие инструкции для 950