background image

 

BIKE IS SUBJECT TO GREATLY REDUCE ITS USEFUL LIFESPAN. IF PROPER CARE AND MAINTENANCE ARE NOT 
PREFORMED YOUR BIKE AND/OR ITS COMPONENTS CAN FAIL CAUSING SERIOUS INJURY OR DEATH.  

GENERAL RIDING INFORMATION 

Once you have inspected your bike and all components are in proper working condition, you are ready to test 
ride your new bike. A few important general rules for riding include but are not limited to:  

-  Strap on your helmet that meets ASTM or CPSC safety testing requirements  

 Have reflectors and lights installed on your bike 

 Use proper hand signals 

 Avoid loose clothing 

 Ride on the correct side of the roadway with flow of traffic  

 Always wear brightly colored and reflective clothing 

 Ride single file if riding with others 

 

− Obey all traffic laws and regulations and traffic signals 

 

 Watch for parked car doors opening unexpectedly 

 Watch for pedestrians stepping out, pets and children playing near roadways 

 Keep a safe stopping distance between you and other vehicles 

 Never carry a passenger 

 Never ride with earbuds or headphones  

 Use caution when crossing railroad tracks and carefully cross at a 90 degree angle 

 Mount a horn or bell on to your bike to signal others of your approach 

 

Braking:

 Your bike is equipped with two hand brakes. One hand brake operates the front brake and the other 

operates the rear. Take time to familiarize yourself with which hand brake stops each wheel. You can 
complete this task by spinning the front wheel and squeezing each brake lever one at a time to determine 
which one stops the wheel from spinning; this would be your front brake. 

When preparing to slow down or stop, gently apply both front and rear hand brakes at the same time being 
careful not to over apply the front brake which could cause you to lose control and fall. Before riding your bike 
for the first time please follow the "Brake Burn in Procedure" in your 

owner’s

 packet. Replacement Pads and 

Rotors are available from Rambo Bikes. Always replace pads and rotors at the same time to ensure maximum 
performance and lifetime. 

AVOID APPLYING SUDDEN OR EXCESSIVE FORCE TO THE FRONT BRAKE SYSEM. DOING THIS CAN CAUSE 
YOUR FRONT WHEEL TO LOCK UP AND YOUR REAR WHEEL COULD LIFT UP AND LOSE CONTACT WITH THE 
GROUND. SLIDE YOUR WEIGHT BACK ON THE SEAT AND APPLY PRESSURE TO BOTH THE FRONT AND REAR 
BRAKES AT THE SAME TIME.  

Содержание PURSUIT R750P-FF-GY


























Отзывы: