background image

 

 

14 

9.1 Mapping wireless commands to give multi-room functionality 

 

Wireless commands can be mapped to additional wireless commands to make multiple 
rooms turn on at once. In the example below the “Hall Scene 1” is mapped to also trigger 
“Kitchen Scene 1”. 

9.2 Triggering Macros from Maps 

When a Macro is used it must be triggered from a map (this could also be from a WCM map, 
WAVFR map etc.). Below Mapping 2 is an example of a map being used to trigger a macro: 
in this case “Start Macro 2”.   

10 Macros 

Macros allow a sequence of actions to take place when triggered by an Event or Map.  The 
HUB can store up to 60 Macros each of which can have a maximum of 32 Steps. 
 
The HUB Macro screen is located from the tab in the HUB device editor. 

 

There are 3 steps in this example Macro: 

-

Room 9, All Channels, Scene 2 

-

Room 17, All Channels Scene 1 

-

Room 49, All Channels Scene 2 

 
With this simply Macro the HUB will just run through the three commands listed. More 
complex functionality can be achieved by using commands in the tables outlined below.  

10.1 Writing Macros  

Macro steps can be one of 4 types: 

WK-HUB

                   Manual Version 1.0.0 

Содержание WK


















Отзывы: