Raisecom RCMS2902-2E1GE-BL Скачать руководство пользователя страница 23

Страница: 23 / 33

Raisecom
RCMS2902-2E1GE-BL Product Description

7 Installation and connection

Raisecom Technology Co., Ltd.

Table 7-1

Connection modes when the Ethernet interface works in self-adaption mode

Ethernet multiplexer

Other device

Connection mode of RJ45 interface

RCMS2902-2E1GE-BL Switch

Straight-through/Crossover

HUB

Straight-through/Crossover

Router

Straight-through/Crossover

NIC

Straight-through/Crossover

When the Ethernet interface works in manual mode, auto MDI/MDIX is disabled. Table 7-2
lists how to connect to other devices in this mode.

Table 7-2

Connection modes when the Ethernet interface works in manual mode

Ethernet multiplexer

Other device

Connection mode of RJ45 interface

RCMS2902-2E1GE-BL Switch

Crossover

HUB

Crossover

Router

Straight-through

NIC

Straight-through

7.2 Installing and removing card



When transporting and installing the RCMS2902-2E1GE-BL, please avoid strong
vibration.



When installing/removing the RCMS2902-2E1GE-BL, please wear the ESD wrist
strap.



Unused cards should be placed in the ESD box or ESD bag.

7.2.1 Installing card

To install the RCMS2902-2E1GE-BL, follow these steps:

Step 1

Wear the ESD wrist strap.

Step 2

Configure the DIP switch on the RCMS2902-2E1GE-BL. For details, see section 4.2
Descriptions of DIP switch.

Step 3

Smoothly insert the RCMS2902-2E1GE-BL into the expansion slot of the chassis along the
rail of chassis and tighten the captive screws.

7.2.2 Removing card

To remove the RCMS2902-2E1GE-BL, follow these steps:

Содержание RCMS2902-2E1GE-BL


































Результаты поиска

Содержание RCMS2902-2E1GE-BL

Отзывы:

Похожие инструкции для RCMS2902-2E1GE-BL

Бренды по названию

Популярные бренды

Raisecom RCMS2902-2E1GE-BL, Описание продукта

Результаты поиска

Содержание RCMS2902-2E1GE-BL

Отзывы:

Похожие инструкции для RCMS2902-2E1GE-BL

Бренды по названию

Популярные бренды