background image

Raisecom 
ISCOM6820-GP (A) Hardware Description 

3 Fiber and cables 

 

 

Raisecom Proprietary and Confidential 

Copyright © Raisecom Technology Co., Ltd. 

25 

 

 

To connect the fiber, align the fiber head with the optical interface. Be careful not to 
damage the ceramic tube inside the optical interface. After snapping the fiber in place, 
rotate the screw sleeve clockwise to fasten the optical interface. 

 

To remove the fiber, rotate the screw sleeve counterclockwise. When the screw sleeve is 
loosened, pull the fiber out. 

3.1.3 Wiring 

Table 3-3 lists the wiring of the fiber. 

Table 3-3

 

Wiring of the fiber 

Wiring 

Local optical interface 

Direction of 

optical signals 

Peer optical interface 

Single-fiber 
connection 

Optical interface 

<-> 

Optical interface 

Dual-fiber 
connection 

Optical interface Tx 

-> 

Optical interface Rx 

Optical interface Rx 

<- 

Optical interface Tx 

 

3.2 Ethernet cable 

3.2.1 Introduction 

The Ethernet cable of the ISCOM6820-GP can be used to: 

 

Connect the Ethernet electrical interface of the ISCOM6820-GP to other devices. 

 

Connect the SNMP of the ISCOM6820-GP to the NView NMS system. 

The Ethernet interface on the ISCOM6820-GP is adaptive to straight-through cable mode and 
crossover cable mode. So both kinds of Ethernet cables can be used. 

The Ethernet cable needs to be made on site. 

3.2.2 Appearance 

Figure 3-4 shows the appearance of the Ethernet cable. 

Figure 3-4

 

Ethernet cable 

 

Содержание ISCOM6820-GP






























































Отзывы: