background image

RKS SW-1500 Diesel Engine ProtoSound 2.0

18

FYS

Remedy

Once in FYS, the engine doesn’t 
go into reverse.

When the FYS enters its last 
sequence the bell automatically 
comes on.

When FYS is enabled, pressing 
the whistle and bell buttons has no 
effect.

I push the direction button but the 
next sound clip in the sequence 
does not play or the engine does 
not come out of FYS after fourth 
press of the direction button.

So that FYS effects can be as 
realistic as possible, 

Proto-

Sound 2.0 disables the 
reversing unit whenever FYS is 
enabled.  This way the engine 
remains still at its stop as the 
operator cycles through the 
FYS sequences.

FYS is programmed to start 
ringing the bell at that point.  After 
approximately 12 seconds it will 
automatically turn off.

Because FYS must control various 
effects in each sequence, Proto-
Sound 2.0 takes control of these 
sound effects until you exit FYS.

Each FYS clip must play for 
approx. 30 seconds before FYS 
will advance to the next step in the 
FYS cycle.  Wait at least 30 
seconds in each FYS sound clip 
before pressing the direction 
button.

Содержание SW 1500 Freight Set























Отзывы: