background image

Self  Charging Battery Back-up

The special NiCad 7-cell 8.4v self-charging battery recharges continuously during 
train operation and  should last for up to five years.  The battery is a dry battery 
that should not leak or cause any damage to your engine.  Depending upon when 
your engine was built, it may need to be charged right out of the box.  If  engine 
sounds seem distorted or garbled at low voltages or become silent when power 
from the transformer is turned off, test the battery to deter mine whether it should 
be recharged or replaced.

Test:

  Put the engine in neutral and 

leave the track voltage at 10-12 volts 
(high enough for the lights to shine 
brightly) for 15 minutes.

Recharge:

  If  the sounds are 

improved at the end of  the 15-minute 
test charge, the battery charge has run 
down and can be recharged.  There 
are a number of  ways you can do this: 

Leave the engine in neutral with track voltage at 10-12 volts for 6-7 hours so 
the battery can fully recharge (if  your engine has a smoke unit, be sure it is 
turned off).  

Use M.T.H.'s battery recharger (sold separately) that plugs into a wall outlet 
and a special port under the engine to recharge the battery overnight without 
leaving it on the track.

Replace:

  If  the sounds are not improved at the end of  the 15-minute test charge, 

it is time to replace the battery.  Available through M.T.H. Parts.  A standard 9v 
alkaline battery can be substituted until your replacement arrives, but since alkaline 
batteries cannot be recharged, it will eventually wear down.  Do NOT use a 6-cell 
7.2v battery.    

RKS SW-1500 Diesel Engine ProtoSound 2.0

15

Remove PS-2 Board

Lift Battery Out

Содержание SW 1500 Freight Set























Отзывы: