Rail King 4-6-4 J3a Hudson Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 34

background image

12 4-6-4 J3a Hudson Steam Locomotive

The following pages contain the operating instructions for Proto-Sound 2.0 RailKing
One-Gauge locomotives when operated with AC output transfomrers in conventional
mode only. Instructions for accessing DCS command mode features accompany the DCS
Remote Control System equipment. These features are only available when using an AC
Transformer equipped with a whistle and bell button.

Proto-Sound 2.0 features are activated by sequences of Bell and Horn button pushes
described below. Please read the full descriptions of each feature before using it. To use
these buttons to activate features rather than to blow the horn or ring the bell, you should
tap the buttons very quickly with a ½-second pause between button presses. You may
need to practice your timing to make this work smoothly.

Proto-Sound 2.0
Operating Instructions

Timing Chart

Total Time Lapse: 1

Seconds

½

Press

Horn

Short &

Firm

½ Sec.

Pause

½ Sec.

Pause

Press

Bell

Short &

Firm

Press

Bell

Short &

Firm

Activating Proto-Sound 2.0 Conventional
Mode Features

(AC Operation Only)

Feature to Be Activated

Button Code:

Passenger Station Announcements
Speed Control On/Off
Lock into a Direction
Reset to Factory Defaults

1 Bell, 2 Horns
1 Horn, 2 Bells (from Neutral only)
1 Horn, 3 Bells
1 Horn, 5 Bells (from Neutral only)

«
...
10
11
12
13
14
...
»

Содержание 4-6-4 J3a Hudson



































Отзывы:

Нет отзывов

Похожие инструкции для 4-6-4 J3a Hudson

Бренд: Makrlin Страницы: 8

Бренд: Oliver Flugmodellbau Страницы: 25

Бренд: Radio Shack Страницы: 4

Бренд: GAME OF BRICKS Страницы: 36

INTERNATIONAL LIGHTHING

Бренд: Sail Classics Страницы: 2

Бренд: LEGO Страницы: 32

Ju 88C-6b Night Fighter exterior

Бренд: Eduard Страницы: 6

Бренд: Wrebbit Страницы: 40

Toot-Toot Drivers Press ‘n’ Go Vehicle

Бренд: VTech Страницы: 3

Бренд: Eduard Страницы: 10

Tribute EP 3D Profile

Бренд: E-FLITE Страницы: 40

Бренд: Bigben Страницы: 52

Бренд: K'Nex Страницы: 16

Batman Power Wing Laptop

Бренд: Oregon Scientific Страницы: 24

Techno Gears Marble Mania Mine Shaft 2.0

Бренд: The Learning Journey Страницы: 72

Бренд: PLAYTIVE JUNIOR Страницы: 16

Waterboard mini pondflyer

Бренд: Stevens Aero Model Страницы: 25

Бренд: Trix Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды