![Raider RD-GHT02 Скачать руководство пользователя страница 19](http://html.mh-extra.com/html/raider/rd-ght02/rd-ght02_user-manual_781702019.webp)
19
STOPPING YOUR ENGINE
To stop the engine, move the ON/OFF switch to the
OFF position.
If engine does not stop, move choke lever to the FULL
CHOKE position.
STARTING YOUR ENGINE
● Fuel engine. Move at least 10 feet (3 me ters) away
from the fueling site.
● Remove the blade cover from the blade before
starting the unit.
● Hold the unit on the ground in the starting position as
shown. Support unit so the blade is off of the ground
and away from trees, bushes, onlookers, etc.
STARTING A COLD ENGINE
(or a warm engine
after running out of fuel)
WARNING:
The cutting blade will be moving once
the throttle lock has been set and the engine is started.
Wear your protec tive equipment and observe all safety
instruc tions.
1. Move the ON/OFF switch to the ON posi tion.
2. Engage the throttle lock as follows:
● Press the throttle lock-out;
● Squeeze and hold throttle trigger;
● press and hold throttle lock, then
● release the throttle trigger
NOTE:
Keep the throttle lock engaged until the engine
starts.
3. Slowly press the primer bulb 6 times.
4. Move the choke lever to the FULL CHOKE position.
5. Pull starter rope handle sharply until en gine sounds
as if it is trying to run, but do not pull rope more than
6 times.
6. Move the choke lever to the HALF CHOKE position.
7. Pull starter rope sharply until the engine runs, but no
more than 6 pulls.
NOTE:
If the engine doesn’t start after 6 pulls (at the
HALF CHOKE position), check to make sure the ON/
OFF switch is in the ON position. Move the choke lever
to the FULL CHOKE position and press the primer bulb
6 times; pull the starter rope 2 more times. Move the
choke lever to the HALF CHOKE position and pull the
starter rope until the en gine runs, but no more than 6
more pulls. If the engine still doesn’t start, It is probably
flooded. Proceed to STARTING A FLOODED ENGINE.
Once the engine starts, allow the engine to run 10
seconds, then move the choke lever to the OFF
CHOKE position. Allow the unit to run for 30 more
seconds at the OFF CHOKE position before squeezing
and releasing the throttle trigger to release the throttle
lock.
NOTE:
If engine dies with the choke lever in the OFF
CHOKE position, move the choke lever to the HALF
CHOKE position and pull the rope until the engine runs,
but no more than 6 pulls.
STARTING A WARM ENGINE
Move the ON/OFF switch to the ON posi tion.
Slowly press the primer bulb 6 times.
Move the choke lever to the HALF CHOKE position.
Engage the throttle lock as directed in STARTING A
COLD ENGINE.
NOTE:
Keep the throttle lock engaged until the engine
starts.
Pull starter rope sharply until engine runs, but no more
than 5 pulls,
Allow the engine to run 10 seconds, then move the
choke lever to the OFF CHOKE position.
Release the throttle lock by squeezing and releasing
the trigger.
NOTE:
If engine has not started, pull starter rope 5
more pulls. If engine still does not run, it is probably
flooded. Proceed to STARTING A FLOODED ENGINE.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the ON/
OFF switch in the ON position and the choke lever in
the OFF CHOKE position and engaging the throttle
lock as directed in the STARTING A COLD ENGINE
section; then, pull the rope to clear the engine of
excess fuel. Starting could require pulling the starter
rope many times depending on how badly the unit
is flooded. If the unit still doesn’t start, refer to the
TROUBLESHOOTING TABLE
Содержание RD-GHT02
Страница 161: ...161 ...
Страница 162: ...162 www raider bg ...