Raider RD-BS06, Руководство пользователя

Страница: 12 / 68

12 www.raider.bg
power cables increase the risk of electric shock.
Failure of the considered instructions may
lead to electric shock, fire and / or severe injuries.
6. Functional description and purpose of the
band grind.
Belt grinding is a manual power with isolation
II class. He is driven by a collector single-phase
motor whose speed is reduced by means of belt
transmission. Belt grinding machine is designed
for dry sanding of flat surfaces of wood materials,
plastics, metals and paint finishes. Not permitted
the use of power tools for activities other than its
intended purpose.
7. Information emitted noise and vibration.
The values are measured according to EN
60745. Level A of the generated noise is usually:
sound pressure level Lp
A
= 91 dB (A); power of
sound Lw
A
= 103 dB (A). Uncertainty K = 3 dB.
Work with a silencer! The resultant value of
vibration (the vector sum of the three directions)
is determined according to EN 60745. Value of the
generated vibrations ah = 4,16 m/s
2
, uncertainty K
= 1,5 m/s
2
. That in this operating manual value for
vibration is measured by the method specified in
EN 60,745 and can be used to compare different
power. The level of vibration varies depending
on the specific activity carried out and in some
cases may exceed that in this guide value. For
an exact estimate of the burden of vibrations
in a working cycle should be recorded and the
intervals in which the power is off or idling. This
can significantly reduce the reporting burden of
vibrations throughout the business cycle.
8. Preparing for the job. Installation of auxiliary
accessories and consumables.
8.1. Prahoulovitelna bag.
In the current activities you can use
prahoulovitelna bag. Insert the nozzle of the bag
firmly on the nozzle opening for outgoing air
stream (6). To operate dust-extraction effectively
empty prahoulovitelnata bag promptly. In
continuous operation a system of dust-extraction
with an additional prahodmukachka.
8.2. Installing and / or replacement of the strip
sandpaper.
Dissolve the locking lever (7) end. Thus
the tape sandpaper (4) is released and can be
removed. Insert a new tape sandpaper (4). In this
careful direction of the arrows inside the strip and
body-power to match. Again, back locking lever
(7) in the starting position.
9. Inclusion and exclusion.
Beware of the voltage of supply network!
Tension of the supply network must comply
with the details shown on the plate of power.
Appliances marked with 230V, can be supplied
with a voltage of 220V.
9.1. To turn the band grind, press and hold the
trigger switch (1). For locking of pressed starting
switch (1) press (2). Exclusion power release
trigger switch (1), respectively, if anchored to
the button (2), first press the short term and then
release the trigger switch (1).
9.2. Adjust the position of the grinding belt
(adjustment of the parallelism of the axes of the
guide rollers).
Include grind. When the grinding belt is
moving, rotate vartoka adjustment of grinding
tape (5), so that the grinding bar to rotate evenly
without depart from the rolls. Assuming grinding
bar to move progressively towards to the body of
grinding (which means that the axes of the rollers
are not parallel) bar will quickly exports.
10. Working with the band grind.
Where possible, work with small force of
constriction to increase the durability of the tape.
The mass of the power is sufficient to achieve
good performance. Excessive increases the
power of the press does not increase productivity
but leads to intensive wear of tools and tape
sandpaper.
Grind parallel to the fiber cross-grinding
leads to the formation of traces of scratches and
undesirable effects.
Keep and refer to the accessories carefully.
Make periodic breaks at work.
Do not throw the tool and do not overload.
11. Service and Support.
11.1. Never use water or any chemical liquid
to clean the band grind. It should be cleaned
with a piece of dry tissue, and accumulated dust
removed with a soft brush. Always keep grinding
dry place and keep the vent on the hull clean.
11.2. Replacing the carbon brushes. Exports
(shorter than 5 mm), up or broken carbon brushes
of the engine should be replaced. Always replace
both the two brushes. Work on replacement
of carbon brushes entrusted only to qualified
person with original spare parts in company
service of RAIDER.
11.3. The repair of your power is best carried
out only by qualified professionals repairers of
RAIDER, which used only original spare parts.
Thus ensuring their safe operation.
12. Preservation of the environment.
In view of environmental power, additional
accessories and packaging must be subjected
to appropriate processing for reuse of the