Raider R50-001 Скачать руководство пользователя

Страница: 36 / 40

Lower oil plug

Upper oil plug

Lower oil plug

Clean or change fuel filter on the engine after removing the fuel filter case.

Tilt the engine up to check the oil level in the tank.

Remove the oil plug by turning Oil plug

Counter-clockwise, then check if the oil level reaches the bottom line of the plug hole.

Oil level

Recommended oil
Use an automatic transmission fluid approved by GM. Recommended oils are as shown below.
•MOBIL: MOBIL DTE #22, MOBIL ATF 220
•SHELL: SHELL DEXTRON-II, SHELL OIL #22 K22
•ESSO: ESSO AUTOMATIC TRANSMISSION OIL

OFF-SEASON

CAUTION

Do not fully unscrew the oil plug with the engine tilted down

Pressurized oil in the oil tank may cause oil to spurt

out.

Note:

Use only recommended gear oil or API (American Petroleum

Institute) oil grade of GL5 SAE #80 - SAE #90. Required volume

approx.

500ml

(16.89 U

fluid oz)

Содержание R50-001









































Результаты поиска

Содержание R50-001

Отзывы:

Похожие инструкции для R50-001

Бренды по названию

Популярные бренды

Raider R50-001, Руководство пользователя

Результаты поиска

Содержание R50-001

Отзывы:

Похожие инструкции для R50-001

Бренды по названию

Популярные бренды