background image

 

6 of 16

 

 

Radar Speed Sign Operation Manual_MN0025 v21.02

 

 

Wi

-

Fi Setup:

 

 

IMPORTANT: 

To configure your sign you will first need to connect to the 

Radarsign Wi

-

Fi.  

 

1)

 

Using a Windows laptop or tablet, Android tablet or smartphone, or iPhone or iPad, disconnect from 
any physical connection you have to any network. Remaining on your network will interfere with your 
attempt to connect to the sign with a Wi

-

Fi connection.

 

2)

 

Make sure your wireless adapter is 

ON

.

 

3)

 

Connect power to your radar speed sign. 

 

4)

 

Upon applying power to the radar speed sign, the radar speed sign BOOT sequence below will be 
displayed (code version 2.14 or later). 

Wait for the test to complete and for the blue blinky light in 

the center of sign to flash before looking for wireless network.   

 

 

5)

 

With your smart phone, tablet, or laptop, find the Radarsign Wi

-

Fi network, RS

-

xxxxxx

 

(the 

x

’ 

sequence is the 6 digit serial number of your sign), and connect.

  

6)

 

You will be prompted for a passkey.

 

Enter the passkey to connect to the network.

 

If you do not see 

 

the network to connect to, power down the radar speed sign for 10 seconds, and then reconnect the 
power. 

 

7)

 

On some devices you will get a warning that this network does not have an internet connection. 

 

No internet is required to connect to the radar sign.

 

 If asked if you wish to stay connected to the 

 

network, say yes. You have successfully connected to your radar sign!

 

8)

 

Once connected, open your web browser. 

 

9)

 

In the address box at the top of your browser, enter the following url: 

10.0.0.1

 

 

The connection will bring up the primary configuration page for your radar sign. 

 

TC

-

400, TC

-

500, TC

-

1000 Boot Messages

 

  

88

 

Display segment test

 

  

SLOW DOWN

 

Display Test 

(TC

-

1000 only)

 

  

.

 

Blinking Decimal Point | Password Reset Period  

(see password reset section)

 

Sn

 

xxxxxx

 

Serial number assigned to the sign.

 

(TC

-

400 starts 30xxxx; TC

-

500S starts 10xxxx; TC

-

1000S starts 20xxxx)

 

Ch

 

xxxxxx

 

Sign firmware checksum

 

  

x.xx

 

Sign firmware version number 

 

TC

-

600 Boot Messages

 

Boot      

 

 

where 

x

’ 

is the number of times the sign has been rebooted without completely finishing 

 

the boot procedure (used to reset wi

-

fi password)

 

Ver 

 

x.xx

 

Sign firmware version number 

 

  

.

 

Blinking Decimal Point | Password Reset Period  

(see password reset section)

 

cksm

 

xxxx 

 

Sign firmware checksum 

 

SD              

 

OK    

 

SD Card test passed 

 

EE                

 

OK    

 

eeprom test passed 

 

TC

-

600 Scrolling Messages 

 

Model 

 

TC

-

600

 

Radarsign model number

 

Serial 

 

xxxxxx 

 

Serial number assigned to the sign. TC

-

600S starts 40xxxx

 

Batt V 

 

13.xx     

 

Battery voltage (in Volts): Minimum operation 10 Volts, full charge  13.9 volts

 

Batt A 

 

1.xx     

 

Battery current (in Amps): 0 if not charging, up to 3.5 Amps if greatly depleted, and getting 

full charge from solar panel on sunny day

 

Solar V 

 

18.xx     

 

Solar panel voltage (in Volts): 17 to 19 volts is a good reading

 

Solar A 

 

1.xx     

 

Solar panel current (in Amps):  0 if not charging, up to 3.5 Amps

 

Содержание TC-400

















Отзывы: