rada Pulse 120 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 48

rada Pulse 120 Скачать руководство пользователя страница 5

5

3. solenoid Valves
Rada sV1015 (HP) solenoid Valve (Direct Acting)

a 1/2" servo assisted solenoid valve, made from wrc approved pa66 reinforced

Fibreglass, fitted with 15 mm compression connections. Flat-faced inserts are

supplied for 1/2" bsp union inlet or outlet connections. an isolating ball valve is

fitted to the inlet to allow the water supply to be isolated. A flow direction arrow on

the valve facilitates correct installation.

Rada sV2022 solenoid Valve (Indirect Acting)

a 3/4" servo assisted solenoid valve made from brass with 3/4" bsp female

connections. A flow direction arrow on the valve facilitates correct installation.

Rada sV2028 solenoid Valve (Indirect Acting)

a 1" servo assisted solenoid valve made from brass with 1" bsp female connections.

The valve is marked "in" on the end to connect the inlet water supply.

Rada sV3022 solenoid Valve (Direct Acting)

a 3/4" lift assisted solenoid valve made from brass with 3/4" bsp female

connections.

A flow direction arrow on the valve facilitates correct installation.

«
...
3
4
5
6
7
...
»

Содержание Pulse 120

















































Отзывы:

Нет отзывов