RACOM RAy3-11 Скачать руководство пользователя

Страница: 239 / 241

Revision History

2018-10-04

Revision 1.0

First issue

2019-04-15

Revision 1.1

RAy3-17 data - preliminary
RAy3 HW variants introduced

2019-05-20

Revision 1.2

Extended

Chapter 5, Configuration

(to reflex FW development)

2019-07-23

Revision 1.3

Updated

Legal Notice

Section 1.6, “Sizes, packaging and labeling”

Section 1.7, “Ordering

codes”

and

Section 10.8, “FCC and IC authorization”

(RAY3-24 FCC for US and IC for

Canada compliance)
Extended

Chapter 5, Configuration

(to reflex FW development)

2019-09-06

Revision 1.4

Updated

Chapter 2, Accessories

Extended

Chapter 5, Configuration

(to reflex FW development)

Extended

Section 10.7.1, “RED Declarations of Conformity”

- DoC RAy3-17

2019-11-11

Revision 1.5

New items in

Chapter 2, Accessories

(marked by '*')

Improved description of some items (

accepted polarities of PoE and power supply

FlowControl parameters in Eth switch

Chapter 8, Troubleshooting

Final parameters for RAy3-17

2020-02-10

Revision 1.6

Extended sections:

PIRL setup

Egress queue setup

and

VLAN setup

(to reflex FW development).

Improved description of some items (new

Pressure equalization

2020-04-09

Revision 1.7

Chapter 2, Accessories

removed sections 2.1. Overview and 2.2 Details (from now

all Accessories are available in

section Accessories

on RAy web site).

Improved description of some items:

Section 1.3.3, “DC power (using ETH1+POE)”
Table 1.1, “Overview of Jirous Class 3 antennas”
Section 1.7, “Ordering codes”
Section 4.2.3.2, “Antenna mounting kit for standard Andrew antennas”
Section 5.5.2.1, “Port setup”

, description of parameter Flow Control

Section 5.6.1.4, “Radio adaptation”

Extended sections:

Section 5.5, “Switch settings”

RSTP status

RSTP setup

(to reflex FW development)

2020-06-22

Revision 1.8

https://www.racom.eu/eng/products/microwave-link.html#accessories

239

Revision History

Содержание RAy3-11


















































































































































































































































Результаты поиска

Содержание RAy3-11

Отзывы:

Похожие инструкции для RAy3-11

Бренды по названию

Популярные бренды

RACOM RAy3-11, Руководство пользователя

Результаты поиска

Содержание RAy3-11

Отзывы:

Похожие инструкции для RAy3-11

Бренды по названию

Популярные бренды