STEP 3: ATTACH FIRST ARM
TIP! It is easiest to attach arms when the corner of the pot rack to which you are connecting the arm hangs slightly past the edge of the table.
That provides clearance for the flared end that extends below the body of the rack.
Now remove the barrel bolt (28A) from one of the corners,
keeping barrel nut (28B) in position. Place a curve arm (22) (2-hole end) on the OUTSIDE of the body. Align the three pieces: (side bar 3A)
on inside, bookshelf end piece (9) in middle, arm (22) on outside), and reinsert the barrel bolt (28A) through the upper hole from the OUT-
SIDE. Repeat for lower hole. Do not tighten barrel bolts firmly until all bolts are in place.
STEP 4: ATTACH OTHER ARM
Repeat STEP THREE for remaining arm.
STEP 5: LEVEL POT RACK ON TABLE
Place assembled rack squarely on table and adjust all parts to be certain they are level and straight. Then tighten all bolts firmly. Remember
~ the back bar (3D) is not attached until the rack is installed on the wall.
STEP 6 ASSEMBLE ACCESSORY SHELF
Note the small holes located in the center of the flat section of each shelf bracket. Two set screws (18E) will be driven through
them to secure the Wood shelf to the brackets.
Center the Wood shelf on top of the brackets (now fixed in position) then with a pencil mark the two set screw points on the un-
der side of the bracket. Pre-drill the marks (or tap a starter hole with a hammer and a small nail) then drive set screws (18E)
into Wood to secure shelf.
STEP 7: MEASURE FOR WALL
After the shelf is assembled, and after the bookshelf rack is squared and tightened, the distance from the center of the holes at top of the
arms to the center of upper holes in back bar should be 9 3/4”. The width between upper holes is 20-3/4”. (see diagram A at bottom of Tog-
gler Instructions on page 4). Use these measurements when determining location of rack on the wall in the installation section below.
NOTE:
Grid and grid brackets will be added AFTER the rack and accessory shelf are attached to the wall.
How to Attach Your Pot Rack to your Wall
TOOLS NEEDED FOR INSTALLATION:
Provided: Installation hardware (anchors, bolts, wall screws and red sleeves)
You will need: level, tape measure, pencil, electric drill and ½” and 1/8” drill bits, hammer and nail.
STEP 1: LOCATION
Decide where you want to place your pot rack. Consider the height of the wall where the pot rack will hang, keeping in mind how far below
the rack your pots and utensils will hang, plus how high above your head you can still easily reach cookbooks, etc. stored on the grid.
On the wall, mark the four points 20-3/4” long by 9-3/4” high where the top of rack arms and back bar will attach. Then tap a small nail
through each mark to be certain a joist is not in the way. NOTE: because your pot rack includes toggle anchors, you DO NOT need to locate
and bolt to studs. See more information under STEP 2 below.
STEP 2: INSTALL TOGGLER DRYWALL ANCHORS
RACK IT UP!’s
drywall togglers eliminate the need to bolt your pot rack to a stud. The steel anchors are very strong and when installed in dry-
wall each drywall anchor holds about 200 lbs. Two anchors hold about 400 lbs. Install the two Toggler drywall anchors (27A) where the two
holes in the tops of the two bookshelf arms are located. Carefully follow Steps 1 through 4 of the Toggler Drywall Anchor instructions found
on the back of this booklet. Do not mount the bookshelf rack at this time.
INSTALL IN WOOD?
If you need to install one or both sides of your rack in wood, use as many of the four wall screws (30A) included, but without a red
sleeve. See back page of this booklet under Step 1.
STEP 3: INSTALL LOWER RED SLEEVE ANCHORS
Follow steps 5) and 6) of the drywall anchor instructions on the back of this booklet. The bookshelf rack is not attached to your wall, but inse-
curely. Please hold the rack in place.
STEP 4: COMPLETE RACK ATTACHMENT AT TOP OF ARMS
Holding the Accessory Shelf between the bookshelf arms and the wall, line up the upper shelf bracket (35) holes with the upper holes in the
bookshelf arms (22). Attach the bookshelf arms and accessory shelf brackets to your wall by carefully following Step 7) of the drywall anchor
instructions on the back of this booklet.
STEP 5: Grid and Brackets
Place the narrow end of the three grid brackets (7B) to the back of the bookshelf body and place the grid over the brackets.
CLEANING:
Your pot rack has a durable powder coat finish designed to provide years of protection. Cleaning is done easily using soap and
a damp cloth. Dry thoroughly after cleaning.
