manualshive.com logo in svg

Racelogic LabSat 3, Руководство пользователя

Поделиться
Скачать
Racelogic LabSat 3 Скачать руководство пользователя страница 39

GNSS antennae require a ground plane to operate correctly. This helps to reduce unwanted reflections of the GNSS
signals caused by nearby objects, and usually the metal roof of a vehicle performs this function. However, if a test
requires an antenna to be placed either off the vehicle, or on a vehicle that does not have a metallic roof, a special

ground plane

antenna must be used. This has an internal ground plane and can operate perfectly without the need for

mounting on a metal surface. Ground plane antennas are available from your LabSat distributor.

Optimising Data Transfer Speeds

• LabSat 3 uses a high speed SD card to record and replay RF data. If you wish to transfer LabSat scenarios from

and to the LabSat 3 Hard Disk Drive (HDD) it is recommend to use a PC that supports USB3.0. The LabSat 3 HDD
supports USB3.0 connection and to get maximum transfer speed then the SD card reader should also have USB3.0
capability.

https://racelogic.support/03LabSat_GPS_Simulators/LabSat_3/LabSat_3_User_Manual/

39

Содержание LabSat 3































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды