manualshive.com logo in svg

Race Technology DL1 MK3, Инструкция по эксплуатации

Поделиться
Скачать
Race Technology DL1 MK3 Скачать руководство пользователя страница 15

15 

Race Technology Ltd. VAT reg. 715 9671 09 

After 12, King Street, Eastwood, Nottingham, NG16 3DA, UK 

Tel: +44 (0) 1773 537620 Fax: +44 (0) 1773 537621 

Email: [email protected]

 

4.3

 

Logging data using the DL1 CLUB 

 

4.3.1

 

Powering up the DL1 CLUB 

Start the vehicle,  wait a few seconds the "Power" LED will come on. Wait for a few 
moments while the GPS receiver acquires a good positional lock. Once the GPS has a 
lock, the GPS LED on the front of the DL1 CLUB will light up.  

4.3.2

 

Insert an SD card 

Take an SD or SDHC card and format it in the PC –  the card must be formatted as 
“FAT32” formatting it as “NTFS” or any other file system will cause unexpected 
behaviour. When formatting is complete, remove the card and place it in the DL1 CLUB 
slot. Once it is inserted wait a few seconds and the status light should start flashing 
indicating that the DL1 CLUB is ready to start logging data. If the status light does not 
start flashing, power down the DL1 CLUB and repeat the above steps. If the status light 
does not flash on / off in equal measure then it could be one of the following problems:  

1.

 

SD Card detection error - one quick flash and off period  

2.

 

FAT file system initialize error – two quick flash and off period  

3.

 

SD card write error – three quick flash and off period  

4.

 

SD card read error – four quick flash and off period 

 

4.3.3

 

 Sampling data 

To sample some data, simply press the "Start/stop logging” button on the front of the 
DL1 CLUB. After a short pause, the "Logging" LED will illuminate, indicating that data 
is being stored on the memory card. Drive the vehicle around for a while (slowly, safely 
and in a responsible manner). To stop sampling press the "Start/stop logging" button 
again. When you have stopped sampling data you can turn off power to the DL1 CLUB 
unit. Never remove the card from the DL1  CLUB whilst it is logging data. This can 
corrupt the card and the data will be lost.  

 

 

 

 

 

 

 

Содержание DL1 MK3














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды